Sunwood Snap-Tight 25GB Glazing Bar
Product number:
LIV-1175-1012
Product information "Sunwood Snap-Tight 25GB Glazing Bar"
25GB Snap-Tight Main Glazing Bar 10/16/25mm Panels
Aluminium Base Bar with PVC-u Cap and End Cap
Strong, extruded aluminium Base Bar with durable PVC-u Cap and decorative End Cap - complete timber rafter main bar for 10, 16 and 25mm polycarbonate. Part of Sunwood's high quality, maintenance-free Snap-Tight range of rafter bars.
The extruded aluminium Base Bars feature a central recess with locking points into which the toothed legs of the PVC-u Cap are located and long-lasting EPDM rubber gaskets to cushion and form a weather-tight seal on the underside of the polycarbonate. The PVC-u Cap has coextruded seals that forms a sound, pressure seal on the top of the polycarbonate once the PVC-u Cap has been pressed firmly into position.
Retro-fitted to existing timber roofs with 10, 16 or 25mm polycarbonate, the 25GB Rafter Main Bar and other Sunwood components can encase and seal problem leak areas while also breathing a new lease of life into the roof. Sunwood is equally effective on new installations too, offering an attractive, low-maintenance, long-life capping solution.
Features & Benefits
- Coextruded Flapper Seal - compress onto glazing for weather-proof seal
- EPDM Gaskets in Base - acts as a seat and seal for glazing
- Aluminium Base Bar - strong and lightweight extrusion
- Flexible System - fits many roof designs and sizes
- Fully-Serviceable - Sunwood components can be easily removed if required
- Maintenance-Free - no annual painting required
- Designed to Integrate - neatly fits other Sunwood products
- Easy-Fit System - designed to ease installation
- 5 Year Guarantee - long product guarantee
Technical Information
| Materials | Base Bar (Aluminium extrusion. EPDB Rubber Gaskets.) Top Cap (PVC-u) End Cap (Plastic with Metal Fixing Bracket) |
| Top Cap Size (w x h x l) | 50mm x 23mm x Various (2.5m/3m/4m/6m) |
| Base Bar Size (w x h x l) | 44mm x 21mm x Various (2.5m/3m/4m/6m) |
| Top Cap Colour | White or Brown |
| Available Lengths | 3m, 4m, 5m and 6m |
Fitting the Sunwood Snap-Tight 25GB Rafter Main Bar
Cut Base Bars to length. Drill fixing holes in the centre of each glazing bar between the upright toothed legs. Fixings should be made at no more than 450mm intervals and around 75mm in from each end. Then ensure Base Gaskets are fitted to either side of Base Bar and screw to the rafter. You can then position the pre-cut and taped polycarbonate and fit Eaves Seal Foam as a draft excluder if desired. All that is then required is to locate the PVC-u Cap over the Base Bar and press/tap firmly into position.
The above is a summary only and not intended as comprehensive fitting instructions.
| Base Material: | Aluminium |
|---|---|
| Capping Material: | uPVC |
| Glazing Compatibility: | Polycarbonate (Multiwall) |
| Glazing Thickness: | 10mm, 16mm, 24/25mm |
| Roof Structure: | Timber Supported |
| Style: | Sunwood Snap-Tight |
Login
Accessory Items
SNAPA Snap-Fix Gable Bar (White)
£34.56*
White SNAPA Snap-Fix Gable Bar for Lean-to Roofs
(Choice of lengths available)
Protective closure for gable end rafters!
Low cost snap-fix glazing bar with closing drip face for gable ends of smaller DIY lean-to roof projects. Tough and long-lasting PVC-u extruded base bar and top cap for polycarbonate sheets. Supplied with End Cap and screw.
Extruded durable PVC-u Base Bar featuring a toothed upstand with locking points for securing the PVC-u top capping. The capping has coextruded seals that form a weather-tight pressure seal on the top of glazing material once the PVC-u capping has been pressed firmly into position over polycarbonate sheets of 10mm, 16mm, 25mm, 32mm and 35mm thickness.
NEW Stronger SNAPA Bar! The new PVC-u SNAPA bars are extruded with significantly thicker walls, which provides greater strength and rigidity over the low-grade aluminium of the old SNAPA bars.
Features & Benefits
Neat closure for gable rafter bars
Durable PVC-u extrusion
Cuts easily with standard hand saw
Simple snap-fix cap fitting
Perfect for simple lean-to roofs
Coextruded seal compresses onto glazing
For 10/16/25/32 and 35mm sheets
Matching Gable Bar option
Low-cost glazing solution
Retro-fitted to existing timber roofs, SNAPA can encase and seal problem leak areas and breath a new lease of life. SNAPA is equally effective on new installations too, offering a capping solution for low-cost lean-to roofs. Common uses for SNAPA Snap-Fix Glazing Bars include: Carports, Greenhouses, Canopies, Covered Walkways and Pergolas.
Unlike many snap-fix rafter capping solutions for lean-to roofs, SNAPA has a matching Gable Bar with an extended drip face for left and right starter rafters of a lean-to roof, so no need to improvise or compromise.
What you get with each SNAPA Gable Bar
Each bar includes, 1 x PVC-u base bar and 1 x PVC-u top capping (both with coextruded gaskets), plus 1 x end cap with retaining screw and screw cover cap.
Technical Information
Materials
Base Bar and Gable Top Capping - PVC-u plastic extrusion with coextruded gasket End Cap - Plastic Fixings - Steel screw and plastic cover cap
Top Cap Size (w x h x l)
52mm x 79.5mm x Various (2m/2.5m/3m/4m/5m/6m)
Base Bar Size (w x h x l)
50mm x 34.5mm x Various (2m/2.5m/3m/4m/5m/6m)
Top Cap Colour
White
Available Lengths
2m, 2.5m/3m/4m/5m/6m
Weight (per m)
1063g
Fitting the SNAPA Snap-Fix Glazing Bar
The following is a brief summary of typical installation. Technical Information and further Fitting Advice is available.
Prepare Base Bars and Top Cappings by cutting to length, ensuring that they will overhang the correct amount over the gutter.
Fix base bar to timber rafter by screwing through central channel every 200-300mm and no more than 75mm from either end.
Prepare polycarbonate sheets by cutting to size, before fitting breather tape and End Closure/Drip Trim. Position over bars and check that any protective film is peeled back from sides. Eaves Seal Foam can be used along eaves to support the underside of the sheets.
Push Top Cappings down into position over the Base Bar upstand and tap down using a soft/rubber headed hammer.
Fit End Caps with supplied screws and caps.
SNAPA Snap-Fix Main Bar (White)
£16.56*
White SNAPA Snap-Fix Main Glazing Bar for Lean-to Roofs
(Choice of lengths available)
Incredibly easy to cut and fit!
Low cost snap-fix glazing bar for smaller DIY lean-to roof projects. Tough and long-lasting PVC-u extruded base bar and top cap for polycarbonate sheets. Supplied with decorative End Cap and screw.
Extruded durable PVC-u Base Bar featuring a toothed upstand with locking points for securing the PVC-u top capping. The capping has coextruded seals that form a weather-tight pressure seal on the top of glazing material once the PVC-u capping has been pressed firmly into position over polycarbonate sheets of 10mm, 16mm, 25mm, 32mm and 35mm thickness.
NEW Stronger SNAPA Bar! The new PVC-u SNAPA bars are extruded with significantly thicker walls, which provides greater strength and rigidity over the low-grade aluminium of the old SNAPA bars.
Features & Benefits
Durable PVC-u extrusion
Cuts easily with standard hand saw
Simple snap-fix cap fitting
Perfect for simple lean-to roofs
Coextruded seal compresses onto glazing
For 10/16/25/32 and 35mm sheets
Matching Gable Bar option
Low-cost glazing solution
Retro-fitted to existing timber roofs, SNAPA can encase and seal problem leak areas and breath a new lease of life. SNAPA is equally effective on new installations too, offering a capping solution for low-cost lean-to roofs. Common uses for SNAPA Snap-Fix Glazing Bars include: Carports, Greenhouses, Canopies, Covered Walkways and Pergolas.
Unlike many snap-fix rafter capping solutions for lean-to roofs, SNAPA has a matching Gable Bar with an extended drip face for left and right starter rafters of a lean-to roof, so no need to improvise or compromise.
What you get with each SNAPA Main Bar
Each bar includes, 1 x PVC-u base bar and 1 x PVC-u top capping (both with coextruded gaskets), plus 1 x end cap with retaining screw and screw cover cap.
Technical Information
Materials
Base Bar - PVC-u plastic extrusion with coextruded gasket Top Cap - PVC-u plastic extrusion with coextruded gasket End Cap - Plastic* Fixings - Steel screw and plastic cover cap
Top Cap Size (w x h x l)
50mm x 34.5mm x Various (2m/2.5m/3m/4m/5m/6m)
Base Bar Size (w x h x l)
50mm x 34.5mm x Various (2m/2.5m/3m/4m/5m/6m)
Top Cap Colour
White
Available Lengths
2m, 2.5m/3m/4m/5m/6m
Weight (per m)
827g
Fitting the SNAPA Snap-Fix Glazing Bar
The following is a brief summary of typical installation. Technical Information and further Fitting Advice is available.
Prepare Base Bars and Top Cappings by cutting to length, ensuring that they will overhang the correct amount over the gutter.
Fix base bar to timber rafter by screwing through central channel every 200-300mm and no more than 75mm from either end.
Prepare polycarbonate sheets by cutting to size, before fitting breather tape and End Closure/Drip Trim. Position over bars and check that any protective film is peeled back from sides. Eaves Seal Foam can be used along eaves to support the underside of the sheets.
Push Top Cappings down into position over the Base Bar upstand and tap down using a soft/rubber headed hammer.
Fit End Caps with supplied screws and caps.
Tip
Exitex Capex Snap Down Glazing Bar
£21.77*
Exitex Capex Snap Down Glazing Bar 10-25mm
(Choice of colour and length)
Low in cost, high in quality!
Strong aluminium base bar with durable, maintenance-free uPVC top capping and end cap. Secures and seals polycarbonate sheets along the timber rafters of wooden conservatory, lean-to roofs, carports and shelters. Suitable for glazing of 10mm, 16mm, 20mm and 25mm thickness.
Base Bars are screwed to the top of timber rafters to provide a seat for the roof material, before Top Cappings are pushed down firmly, until their toothed legs grip the relevant locking point on the Base Bar up-stand. Weather sealing is provided by rubber flapper seals that are coextruded along the top capping, whilst the underside is sealed by long-lasting EPDM rubber gasket that fits along either side of the base bar.
Features & Benefits
Easy-fit System - screw base to rafter and snap capping down
Top Cap Flipper Seal - compression gasket for weather-proofing
Rubber Base Gaskets - act as a seat and under-seal for glazing
Aluminium Base Bar - strong and lightweight extrusion
Long-lasting Material - durable and UV-stable parts
Maintenance-free - top capping needs no annual painting
Exitex are a leading manufacturer of weather-proofing products, with over 40 years’ experience in the design and manufacture of aluminium and uPVC glazing solutions, including Capex Snap Down.
Technical Information
PropertyValue
Colour
White, Brown and Anthracite Grey (Base Bar is mill finished aluminium)
Width
45mm (Base Bar), 50mm (Top Capping)
Length
2.5m (8ft 2in), 3m (9ft 10in), 4m (13ft 1in), and 6m (19ft 8in)
Compatibility
10mm, 16mm, 20mm and 25mm thick polycarbonate sheets
Materials
Aluminium extrusion with EPDB rubber gaskets (Base Bar), PVC-u with rubber flipper seal (Top Capping), PVC-u (End Cap)
Fitting the Exitex Capex Snap Down Glazing Bar
The following is offered as a guide to typical installation, and not intended as comprehensive fitting instructions.
Cut Base Bar and Top Capping to same length as polycarbonate sheet
Fit EPDM rubber gasket (may need to be torn into two along the length) to track on either side of Base Bar
Pre-drill fixing holes along length of base bar and between toothed up-stand
Fixings should be no more than 500mm apart and within 100mm from either end
Screw the Base Bars to rafters using 5mm wood screws
Peel protective film from edges of polycarbonate sheets to prevent being strapped by glazing bar
Position Top Capping over Base Bar and push legs firmly into up-stand to ensure seal
Fit end closure to polycarbonate sheet, using thin bead of silicone on underside of top face
Apply a little silicone sealant to underside of End Cap top lip and push firmly onto glazing bar
Additional considerations
It is assumed that polycarbonate sheet length is cut with allowance for a 50mm overhang into the gutter.
A glazing width deduction of 21mm from rafter centres will allow for Base Bar up-stand, plus expansion and contraction.
Fixing buttons can be used along eaves or purlins to secure sheets that are large, or in exposed locations.
Capex Snap Down works best with roofs over 5° pitch.
Accessory Items
SNAPA Polycarbonate H-Section (Clear)
£16.55*
Clear H-Section Joining Strip for Polycarbonate Sheets
(Choice of thickness and length)
Provides a strong rigid seal!
Clear uPVC plastic H-profile joining strip for 6mm, 10mm or 16mm multi-wall polycarbonate sheets along sidth or length. Provides increased coverage and greater compression for a more reliably sealed joint.
Available for 6mm, 10mm and 16mm thick multiwall polycarbonate sheets and in lengths of 2m (6ft 7in), 3m (9ft 10in) and 4m (13ft 1in). Useful as a muntin bar to increase length of sheet coverage or as a joining strip along the length to increase the width.
Features & Benefits
Discreet transparent appearance
Designed for tighter hold on sheets
Use with 6/10/16mm polycarbonate
Use as edge trim or end closure
Strong and lightweight
Simple push-fit design
A great ancillary product to the SNAPA Snap-Fix Glazing Bar system, which is a highly effective and low-cost lean-to roof capping solution for timber rafters. Common uses for SNAPA include: Carports, Greenhouses, Canopies, Covered Walkways and Pergolas.
Technical Information
Materials
PVC-u
Compatibility
6mm, 10mm or 16mm thick sheets
Fitting the H-Section Trim
To fit, simply push the h-section onto first one sheet and then push the second sheet into the open side. Ensure that there is a little breathing space between the end of the sheet and the internal face of the h-section. It is often recommended to run a bead of neutral cure silicone on the underside of the top lips, to help seal and secure.
Lean-to Roof Wall Flashing Trim
£46.12*
Wall Flashing Trim for Lean-to Roofs
(Choice of colour and length)
Protection where glazing bars meet wall!
Wall flashing trim for weather-proofing lean-to roof at host wall. Made from durable powder-coated aluminium extrusion with integrated foam gasket, and suitable for most glazing bar systems, including ALUKAP-XR and SNAPA.
Sealing over the wall plate, where glazing bars meet the host wall, can be troublesome, and this area is vulnerable to water ingress, so needs care and attention. This aluminium Wall Flashing is designed to help with that challenge, and can be used with the SNAPA snap-fix, and ALUKAP-XR screw-down, along with most other such glazing bar systems.
Features & Benefits
Protects and seals - integrated foam gasket seal
Flexible application - suitable for 3-20° pitch
Strong and durable - powder-coated aluminium
Simple fitting - cut, silicone, screw fix, and flash
Low-maintenance - no annual painting required
Highly versatile - use SNAPA, ALUKAP-XR and more
Did you know? This wall flashing has an expected life expectancy of over 20years!
What you get with each Wall Flashing
Each wall flashing is supplied as an aluminium extrusion, with closed-cell foam gasket for sealing against roof sheeting and over the top cappings.
Technical Information
Materials
Wall Flashing Trim - Powder-coated aluminium extrusionGasket - closed-cell foam
Flashing Up-stand Height
78mm
Flashing Projection
104.5mm
Length
2m, 3m or 6m
Colour
White, or Dark Brown
Weight (per m)
540g
Fitting the Wall Flashing Trim
The following provides a brief summary of typical installation. We recommend that customers who are new to this product, refer to the manufacturers technical brochure, for further fitting advice.
With bars and roof sheets in position, determine the required length of Wall Flashing and cut to size.
Sit the Wall Flashing in position, and mark top capping locations on the foam gasket. At the marks, cut out gasket, to provide an even compression seal over cappings and roof sheets.
Apply silicone sealant along the rear of the up-stand, which will push flush against the wall.
Position Wall Flashing against wall, and push down onto bars and roof sheets.
Fix to wall using suitable stainless steel screws.
Variants from £40.30*
16mm Polycarbonate End Closure
£4.44*
End Closure for 16mm Polycarbonate Sheets
(White, Brown or Anthracite Grey)
Seal and protect the ends of your polycarbonate sheets
Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket.
End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting.
Features & Benefits
Seals open end of polycarbonate sheet
Helps prevent dust and insects entering the sheet
No need to use silicone to seal the end closure
Co-extruded gasket stops water penetration from above
Protects vented anti-dust breather tape
Drip design prevents water from being blown back towards the roof
Drainage holes reduce condensation and moisture
IMPORTANT SIZE INFORMATION These end closures are designed to fit 16mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey.
Extend the life of your roof
With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening.
These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure.
Technical Information
Colour
White, Chocolate Brown, and Anthracite Grey
Material
PVC-u
Glazing Thickness
16mm
Length
2.1m (White and Chocolate Brown), 2.5m (Anthracite Grey)
SNAPA Polycarbonate C-Section (Clear)
£11.58*
Clear C-Section Edge Protector Trim for Multiwall Polycarbonate Sheets
(Choice of thickness and length)
Closes open ends of sheets and protects the edges!
Dual-purpose transparent uPVC plastic c-profile extrusion. Fits across twin-wall and triple-wall polycarbonate sheets to act as an end closure that protects breather tape and prevent ingress of water and insects, or can be used along the length as a protective edge trim.
Available for 10mm and 16mm thick multiwall polycarbonate sheets and in lengths of 2m (6ft 7in) and 3m (9ft 10in). A great product for protecting edges when over-sailing sheet directly across starter rafters.
NEW Stronger SNAPA Bar! The new PVC-u SNAPA bars are extruded with significantly thicker walls, which provides greater strength and rigidity over the low-grade aluminium of the old SNAPA bars.
Features & Benefits
Discreet transparent appearance
Designed for tighter hold on sheets
Use with 10mm or 16mm polycarbonate
Use as edge trim or end closure
Strong and lightweight
Simple push-fit design
A great ancillary product to the SNAPA Snap-Fix Glazing Bar system, which is a highly effective and low-cost lean-to roof capping solution for timber rafters. Common uses for SNAPA include: Carports, Greenhouses, Canopies, Covered Walkways and Pergolas.
Technical Information
Materials
PVC-u
Size
For 10mm Sheets: 20mm (top lip), 14mm (front face), 12mm (bottom lip), 2m or 3m (length)For 16mm Sheets: 20mm (top lip), 14mm (front face), 12mm (bottom lip), 2m or 3m (length)
Compatibility
10mm or 16mm thick sheets
Fitting the C-Section Trim
To fit, simply push the c-section onto the sheet and ensure that there is a little breathing space between the end of the sheet and the internal face of the c-section. It is often recommended to run a bead of neutral cure silicone on the underside of the top lip, to help seal and stick.
Sunwood Snap-Tight Edge Trim
£8.58*
Edge Trim F-Section for Snap-Tight Glazing Bar
(Choice of thickness, length and colour)
Neat closure for open side of Snap-Tight Bar when used as a gable!
Durable PVC-u trim with co-extruded rail that clips securely into the track on Sunwood Snap-Tight aluminium base bars, closing the open side and providing a surface onto which the glazing bar top cap can compress to form a water tight seal.
This product is available to suite 10mm, 16mm or 25mm thick polycarbonate sheets, a choice of lengths and in white or chocolate brown colour.
Features & Benefits
Long-life material - tough PVC-u extrusion
UV stable PVC-u - resists damage from Sun
Designed for Sunwood Snap-Tight glazing bars
Use with 10mm, 16 and 25mm sheets
Fully-serviceable - easily removed if required
Maintenance-Free - no annual painting required
Easy-Fit System - simple to install
5 Year Guarantee - long product guarantee
Technical Information
Finishes
White or Brown
Material
PVC-u
Width
28mm
Height
34mm (10mm), 40mm (16mm), 48mm (25mm)
Length
2.5m (10mm only), 3m and 4m
Application
F-Section for 10mm, 16mm or 25mm polycarbonate sheetsEdge Trim for Sunwood Snap-Tight Glazing Bars
Fitting the Sunwood Edge Trims
With the glazing bar Top Cap removed, ensure that the rubber gasket strip is only fitted to the side holding polycarbonate roof sheet and not the open side. The rail, on the underside of the Edge Trims botton lip, should be clipped into the track which the rubber gasket would normally be fitted. This is enough to ensure that the edge trim stays secure and provides a surface for the top capping.
10mm Polycarbonate End Closure
£8.20*
End Closure for 10mm Polycarbonate Sheets
(White, Brown or Anthracite Grey)
Seal and protect the ends of your polycarbonate sheets
Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting.
End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provide decorative protection to the vulnerable ends of polycarbonate sheeting.
Features & Benefits
Seals open end of polycarbonate sheet
Helps prevent dust and insects entering the sheet
Protects vented anti-dust breather tape
Drip design prevents water from being blown back towards the roof
Drainage holes reduce condensation and moisture
IMPORTANT SIZE INFORMATION These end closures are designed to fit 10mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey.
Extend the life of your roof
With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material.
Technical Information
Colours
White, Chocolate Brown and Anthracite Grey
Material
PVC-u
Glazing Thickness
10mm
Length
2.1m (White and Brown), 2.5m (Anthracite Grey)
Variants from £3.97*
25mm Polycarbonate End Closure
£4.82*
End Closure for 25mm Polycarbonate Sheets
(White, Brown or Anthracite Grey)
Seal and protect the ends of your polycarbonate sheets and glass units
Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket.
End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting.
Features & Benefits
Seals open end of polycarbonate sheet
Helps prevent dust and insects entering the sheet
No need to use silicone to seal the end closure
Co-extruded gasket stops water penetration from above
Protects vented anti-dust breather tape
Prevents UV light breaking down the glass units seal
Drip design prevents water from being blown back towards the roof
Drainage holes reduce condensation and moisture
Extend the life of your roof
With three sides protected by glazing bars and ridge capings, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening.
These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure.
Glass units are also protected by end closures. Even though the glass roof units are sealed they can still be damaged by the elements - UV light can break down the seal and cause the unit to fail.
Technical Information
Finishes
White, Chocolate Brown or Anthracite Grey
Material
PVC-u
Glazing Thickness
25mm
Length
2.1m (White and Brown), 2.5m (Anthracite Grey)