Ventilated Eaves Starter Bar for Envirotile Roof Tiles (600mm long) Prevents tile uplift at the eaves! The Eaves Starter Bar is an integral part of the Envirotile roof system, and is designed to secure the first course of tile over the eaves, whilst allowing escape of any built-up condensation. Multiple sections of Eaves Starter Bar are used end-to-end to span the width of a roof and are fixed with stainless steel screws over the fascia board, with felt and felt support tray beneath. Features Eaves Starter Bar & Envirotile Prevents tile uplift - locks first course of tile Easy to fit - just screw fit bar and clip in tile Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Technical Information MeasurementValue Size (l x w x t) 600mm x 48mm x 12mm Weight 82g Roof Tile Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Tile Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Tile Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Tile Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Tile Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Eaves Starter Bar and the Envirotile 8Fix Synthetic Plastic Roofing Roof should be prepared as normal, with felt support trays, roof felt and battens. Then working from right-hand-side, secure Eaves Starter Bar over fascia board with stainless steel screws. Low edge of first course tile just clip into place. Envirotiles which are extremely simple to fix, with slide locks for quick alignment and security, should be laid using the 3-step layout procedure. Envirotiles can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

  Envirotile Synthetic Slate Roof Tiles Plastic Roofing (Slate Grey, Black, Brown and Terracotta) The only tile with 8Fix locking for quick and secure fitting! Lightweight and virtually unbreakable recycled roof tile with natural slate finish. Features a unique watertight 8Fix system that fits quickly and securely, whilst outperforming all other synthetic tiles in severe weather conditions. Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Features & Benefits Interlocking fixing - installs quickly and stops uplift Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under severe wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 365mm x 325mm x 11mm (half and double tile available) Coverage (per m2) 280mm Gauge (22.5° - 90°) = 11.9 single tiles 265mm Gauge (22.5° - 90°) = 12.6 single tiles 250mm Gauge (12.5° - 22.5°) = 13.4 single tiles Weight 645g per tile (approx. 8Kg/m2) Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile Lay using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Slate Half Tiles (Slate Grey, Black, Brown and Terracotta) Half size tile reduces cost and wastage! Lightweight and virtually unbreakable half tile with natural slate finish, for initiating a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Features the 8Fix system that fits quickly and securely. Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Features & Benefits Reduces waste and work - convenient half tile size Interlocking fixing - installs quickly and stops uplift Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 365mm x 175mm x 11mm (full and double tile available) Weight 379g per half tile (full tiles are 649g, approx. 8Kg/m2) Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile The half tile can be used on alternate runs to create the required borken half bond, and for detailing. Envirotile should be layed using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirolay HR Underlay from Envirolite (1.3m wide x 25m long) The premier roofers underlay! Strong, high performance fire resistant roof underlay, for use on all cold or warm roof types, in all 5 UK wind pressure zones. Envirolay Premier has been fully tested and exceeds the requirements of BS 5534 so you can rest assured you are using an underlay that is fit for purpose. Features of Envirolay & Envirotile Fire resistant material Can be used in all UK zonal areas 1-5 Suitable for all cold or warm roof structures Use with Envirotile on cold roof for BS476-3 compliance Fully tested to BS5534 Annex A Fully Exova Tested with Envirotile to DD CEN/TS 1187 test4 - Brooft4 Please note that on a cold roof type with the Envirotile roof system, to conform to Fire Standard BS 476-3, only Envirolay is approved for full use. On warm roof applications, other underlay can be used with Envirotile. Part of the Envirotile Synthetic Slate system Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Technical Information MeasurementValue Size (width x length) 1.3m x 25m Application Suitable for use on all cold or warm roof structures. Wind Zone / Batten Gauge 345mm Batten Gauge (battened lap) = Zone 1 to 5 >2040250mm Batten Gauge Battened Lap = Zones 1 to 5345mm Batten Gauge Taped Lap = Zones 1 to 5 >4500 Credentials BS5534 Annex A (Bre tested), DD CEN/TS 1187 test4 - Brooft4 (Exova tested). Fitting Envirolay and the Envirotile 8Fix Synthetic Plastic Roofing Envirolay should be fitted with at least 100mm lap over felt support tray, and at least 150mm lap over each course. Envirolay tape (GSPDST) can be used to seal overlap for added protection against uplift during heavy winds. Starting on the right, roll out and fix to centre of rafters with clout nails. Ensure 10-15mm sag between rafters to allow any moisture build up to run down. Envirolay should be finished 25mm short of the ridge apex, and 150mm up wall face of any abutment. Envirotiles which are extremely simple to fix, with slide locks for quick alignment and security, should be laid using the 3-step layout procedure. Envirotiles can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Slate Double Tile (Slate Grey, Black, Brown and Terracotta) Secures ends and speeds up long runs! Double tiles ensure adequate fixing points at the end of each course, and are especially useful on hipped roofs. Lightweight and virtually unbreakable with natural slate finish, double tiles fits quickly and securely as discreet filler tiles for long runs. Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 6 double tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Features & Benefits Extra fixing points - secures verge, hips and valleys Reduces waste and work - convenient half tile size Interlocking fixing - installs quickly and stops uplift Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 365mm x 630mm x 11mm (half and full tile available) Coverage (per m2) Coverage (per m2) 280mm Gauge (22.5° - 90°) = 6 double tiles 265mm Gauge (22.5° - 90°) = 7 double tiles 250mm Gauge (12.5° - 22.5°) = 7 double tiles Weight 1.342Kg per double tile (full tiles are 649g, approx. 8Kg/m2) Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile Double tiles can be used at the ends of each course to ensure adequate fixings, especially on hipped roofs, and are great as a filler tile for long runs. Envirotile should be layed using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.