Ventilated Eaves Starter Bar for Envirotile Roof Tiles (600mm long) Prevents tile uplift at the eaves! The Eaves Starter Bar is an integral part of the Envirotile roof system, and is designed to secure the first course of tile over the eaves, whilst allowing escape of any built-up condensation. Multiple sections of Eaves Starter Bar are used end-to-end to span the width of a roof and are fixed with stainless steel screws over the fascia board, with felt and felt support tray beneath. Features Eaves Starter Bar & Envirotile Prevents tile uplift - locks first course of tile Easy to fit - just screw fit bar and clip in tile Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Technical Information MeasurementValue Size (l x w x t) 600mm x 48mm x 12mm Weight 82g Roof Tile Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Tile Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Tile Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Tile Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Tile Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Eaves Starter Bar and the Envirotile 8Fix Synthetic Plastic Roofing Roof should be prepared as normal, with felt support trays, roof felt and battens. Then working from right-hand-side, secure Eaves Starter Bar over fascia board with stainless steel screws. Low edge of first course tile just clip into place. Envirotiles which are extremely simple to fix, with slide locks for quick alignment and security, should be laid using the 3-step layout procedure. Envirotiles can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Slate Double Tile (Slate Grey, Black, Brown and Terracotta) Secures ends and speeds up long runs! Double tiles ensure adequate fixing points at the end of each course, and are especially useful on hipped roofs. Lightweight and virtually unbreakable with natural slate finish, double tiles fits quickly and securely as discreet filler tiles for long runs. Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 6 double tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Features & Benefits Extra fixing points - secures verge, hips and valleys Reduces waste and work - convenient half tile size Interlocking fixing - installs quickly and stops uplift Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 365mm x 630mm x 11mm (half and full tile available) Coverage (per m2) Coverage (per m2) 280mm Gauge (22.5° - 90°) = 6 double tiles 265mm Gauge (22.5° - 90°) = 7 double tiles 250mm Gauge (12.5° - 22.5°) = 7 double tiles Weight 1.342Kg per double tile (full tiles are 649g, approx. 8Kg/m2) Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile Double tiles can be used at the ends of each course to ensure adequate fixings, especially on hipped roofs, and are great as a filler tile for long runs. Envirotile should be layed using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Tile Ridge Cap (Slate Grey, Black, Brown and Terracotta) Quicker fitting of a more secure ridge! Easy to install interlocking plastic ridge capping for quick dry-fix covering of roof apex. Part of the Envirotile roof system, a lightweight and virtually unbreakable recycled roof tile with natural slate finish. Tiles in the Envirotile system have the unique watertight 8Fix feature, so fit quickly and securely, whilst outperforming all other synthetic tiles in severe weather conditions. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Features & Benefits Interlocking ridge caps - quick fitting and secure Dry-fix ridge system - no need for sand and cement Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Technical Information MeasurementValue Size (l x w x t) 425mm x 245mm x 105mm Weight 549g Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Tile Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Tile Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Tile Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Tile Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Main Ridge Caps and the Envirotile 8Fix Synthetic Plastic Roofing The main Ridge Caps interlock with one another along the ridge and are screwed securely onto the bedded apex batten. Envirotiles which are extremely simple to fix, with slide locks for quick alignment and security, should be laid using the 3-step layout procedure. Envirotiles can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Slate Dry Verge (3m in Anthracite Grey, Brown and Terracotta) Neat secure closure to roof verge! Lightweight and durable plastic continuous dry verge for Envirolay tiles, and other synthetic and natural roof slates. Protects against wind uplift and unlike mortar verges, it won't crack as a result of weathering and movement. Features & Benefits Natural or synthetic tiles - use with most natural and synthetic slates No weathering - does not crack due to movement or weathering like bedded mortar Neat finish - attractive continuous edge to the roof Windproofs - prevents wind from getting behind the tiles and lifting them off the roof Quick and easy fitting - loved by slaters, once they have used the product, for many of the above benefits Kind to environment - made from recyclable plastic and dolomite limestone BBA & BS Certified - complies with BS476 part 3 - an AA fire rating is achieved for insulation on boarded roofs Part of the Envirotile system Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 3m x 86mm x 98mm. Dry Verge Joint Clips are available for connecting over long verges. Weight 1.483Kg per length (approx. 500g/m) Material Recycled plastic. Colour Anthracite Grey, Brown or Terracotta. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile Fit the first Envirotile roof tile onto the Eaves Bar at the gable end, and position the end of the continuous dry verge directly in line and flush with the bottom edge of the overhanging roof tile. Place the inner sleeve directly onto the exposed batten ends that have been cut flush with the gable roof edge. Fix with 30mm stainless steel screws downwards into the top of the battens making sure the dry verge unit is perfectly in line with the verge. Fix a Dry Verge Joint Clip with screw fixings, if required to join lengths of continuous dry verge, when rafters are longer than 3m. Mitre cut the continuous dry verge so that the ends abut at the apex. Lay using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.

Envirotile Synthetic Slate Half Tiles (Slate Grey, Black, Brown and Terracotta) Half size tile reduces cost and wastage! Lightweight and virtually unbreakable half tile with natural slate finish, for initiating a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Features the 8Fix system that fits quickly and securely. Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion. Features & Benefits Reduces waste and work - convenient half tile size Interlocking fixing - installs quickly and stops uplift Lightweight roofing - 80% lighter than a concrete tile Low-pitch solution - pitched from 12.5° to vertical Virtually unbreakable - easy to transport and fit Smaller lap - lower cost per metre and less work Reduces build costs - easy to handle and quick to fit Improved surface - easy grip and anti-fungal Fully recyclable - made from recycled plastics 25 Year guarantee - long service and peace of mind Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products. Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points. Envirotile is weather tested to 147mph winds and fully guaranteed to perform under sever wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation. Technical Information MeasurementValue Size (l x w x t) 365mm x 175mm x 11mm (full and double tile available) Weight 379g per half tile (full tiles are 649g, approx. 8Kg/m2) Material Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene. Batten Recommendations Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres. Bond Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings. Guarantee 25 years against material product defects or failure to perform under normal use Credentials EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed Fixing 30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch) Cutting Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting Storage Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation. Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile The half tile can be used on alternate runs to create the required borken half bond, and for detailing. Envirotile should be layed using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.