EasyVerge U Dry Verge Unit (Available in Grey, Brown, Terracotta and Black) No nonsense - one units does left or right! High quality, UV stable plastic dry verge units that can be used either way round, so no need for separate left and right units. Installs quickly and easy with almost any tile type. Mortar-free, maintenance-free method of securing almost any tile type along roof verge. Unique design combines ease of installation with exceptional holding, so tiles are held firmly in place and not vulnerable to wind dislodgement. Features & Benefits Universally handed - no need for left and right units Quick fit design - 36 units in under 5 minutes Versatile - fit to any type of roof tile High compression - roof tiles held firm in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Mortar-free - eaves remains protected but well ventilated Technical Information MeasurementValue Colour Grey, Brown, Terracotta or Black Material PVC-u Length 410mm Height 168mm Depth 50mm Tile Compatibility EasyVerge U Dry Verge Units are compatible with most makes and profiles of interlocking tiles. Batten Gauge 290mm – 345mm Roof Pitch 15° to 45° Quick and Easy Fitting The unique design of Easy Verge U means that it can be fitted extremely quickly. In fact, this video demo shows that it's possible to fit a whole gable end of 36 units in under 5 minutes! Basic Procedure Fit optional Starter to low end of verge Position Unit over Starter with top flap over first tile Push upwards to engage with Starter and trap flap under overlapping tile Fix in place through a pre-drilled fixing hole with ring shank nails Hook next Unit under previous and pull top flap up and over Push Unit upwards engaging with previous and align with tile Nail the Unit in place and repeat for remaining units * The above fitting notes are intended as a guide, not comprehensive instructions.

Ridge F PLUS 'Dry Fix' Ridge/Hip Kit (6m) (Available in Black or Terracotta) NEW Ridge F PLUS is more streamlined and more secure! Dry Fix F Plus forms a ridge that is resistant to water, whilst allowing the roof to breath. Offers quick and simple mechanical fixing of almost all ridge tiles, and guaranteed for 20 years. The ventilated Ridge Roll provides the equivalent of 5mm continuous airflow and it's malleable, crimped aluminium skirt with flexible ridge tile Unions are the key components that make this kit so effective. Together, they offer long term security with a quality water seal. Suitable for concrete, clay ridge tiles, and compatible with slate and tile profiles. Features & Benefits Quick and easy to fit - no special tools or skills required Allows the roof to breath - provides a ventilated ridge Fully serviceable - easy to maintain even after many years Glass filled nylons - increased strength, resistance and stability Discreet design - provides a more streamlined appearance Can also be used on hips - requires dedicated Hip Trays Long-life durable fixings - Stainless Steel and Nylon 20 year guarantee - British Standard product you can trust The Easy Ridge F complies with BS 5250 and BS 5534 and is manufactured to DIN 4108/3. The dry fix system is resistant to freeze/thaw cycles plus thermal expansion/contraction and is recommended by NHBC. CAN BE USED ON HIPS! Ridge F Plus is great on hips too! Just requires a dedicated Hip Try to be fitted over the ventilated roll (see our Hip Accessory Kits). 6m Ventilated Ridge Roll Polypropylene mesh fabric with spine and malleable crimped aluminium skirt, which makes it easy to dress over contoured tiles. Underside of skirt has high butyl adhesive strips for sealing against roof tile. Material Polypropylene and Aluminium Length 6,000mm Width 300mm Colour finge and clips Black or Terracotta Ridge Unions (13 Pack) Tough and flexible Nylon unions that you can use with almost all ridge tile, including angled and half round profiles of concrete or clay. Adjoining ridge tile sit on either side of a union up-stand and are trapped securely with 3 'ratchet' clips , the central one featuring a screw port to fasten to ridge batten with provided stainless steel screw. Enough unions are supplied for standard length ridge tiles over 6m. Additional unions may be required if ridge tiles are shorter than 400mm. Material Nylon (union), Glass filled nylon (ratchet clips), Stainless Steel (screw fixings) Length 304.8mm Width 50mm Height 20mm Colour Black Each of the 13 x Unions is supplied with 1 x Large Ratchet Clip, 2 x Small Ratchet Clips and 1 x Stainless Steel screw.* Measurements taken when union flat. Ridge Batten Straps (10 Pack) Stainless steel straps, designed to be folded over ridge fixing battens and nailed to roof truss rafters through pre-drilled holes. Supplied with approximately 45 x nails. Material Stainless Steel (brackets), Stainless Steel (clout nails) Strap Length 400mm Strap Width 25mm Supplied with a quantity of Stainless Steel cloat nails. The kit is supplied with fitting instruction to help you through the process but be assured, fitting is quick and easy compared to mortar fitting and other dry-fix systems. Install roof underlay and battens as normal but finish underlay 5-30mm short of apex on either side and don't fit last batten Build up the ridge batten to required height (two battens are usually sufficient), and using stainless steel batten straps. Fix top tiling batten with minimum 10mm air gap between it and ridge batten, then lay and fix the tiles as normal Unroll EasyRidge F PLUS over the ridge batten, ensuring coverage over top course of tile and secure with corrosion resistant staples or nails Remove release paper from the butyl adhesive strips and dress neatly onto the dry/clean tiled surface Prepare the Unions by lightly pressing one large fixing clip (in the central slot) and 2 smaller ratchet clips Place end ridge tile and insert the prepared ridge union under and between the ridge tiles. Loosely tighten the 3 ratchet clips down onto the union. Secure to ridge fixing batten with Stainless Steel screw through central fixing clip Pushing the ratchet clips into the union to secure. Continue process along the ridge

Butyband Lead Flashing Tape from Soudal (10m long in choice of width) Safe to use on polycarbonate roof sheets! Butyband is a versatile, high quality self-adhesive butyl rubber based flashing tape, for reliable sealing and repair work with a traditional lead appearance. This flexible peel and seal tape is ready to use and is easily cut and shaped as required. Idea for a variety of applications, including sealing around chimneys, windows and doors, glass and polycarbonate sheets, metal, plus general sealing and repair. Features & Benefits Excellent adhesion – sticks quickly and soundly to many substrates Elastoplastic material – strong plastic material with elastic rubber properties Waterproof – strong barrier against water ingress Long-lasting – resistant to UV and harsh weather conditions Highly malleable - can be cut, shaped and formed More authentic appearance – blends with existing lead These 10m (32ft 10in) long rolls of Butyband, are available in a choice of five widths, 75mm (3in), 100mm (4in), 150mm (6in), 225mm (9in) and 300mm (12in). Technical Information Measurement Value Width 75mm (3in), 100mm (4in), 150mm (6in), 225mm (9in) and 300mm (12in) Length 10m (32ft 10in) Thickness 0.6mm Moisture Vapour Transmission 2.5 g/m² per 24 hrs Specific Gravity (DIN 53479) Approx. 1,00 g/cm³ UV Stability Good Temperature Resistance -30°C to +80°C Application Temperature +5°C to +35°C Compatibility Various porous and non-porous substrates, such as wood, concrete, bricks and other common building industry materials. Surfaces should be clean, dry and free of grease and loose particles. A primer is recommended on very porous surfaces and a compatibility test is recommended. Using Soudal Butyband Lead Flashing Tape Cut Butyl tape to the desired length before removing the protective paper and apply the tape to the prepared surface. Press firmly to ensure a perfect seal and smooth creases carefully by pressing or using a pressure roller. If one strip of Butyband is to join another, make sure that there is an overlap of at least 50mm.

EasyVerge U Eaves Starter Park Eaves Closure fitted Close up of Eaves Closure Starter Pack for EasyVerge U Available in Grey, Brown, Terracotta or Black Part of the no nonsense, easy-fit system! Ensures secure fit of EasyVerge U units to roof verge. Includes Starters for improved fixing of eaves-end units and Blanking Plates for covering fixing holes of ridge-end units. In addition to providing a better fix, Starters also act as end caps to provide an attractive finish and prevent infestation. Part of EasyVerge U, the mortar-free system for securing almost any tile type along roof verge. EasyVerge U's unique design combines ease of installation with exceptional holding, so tiles are held firmly in place and not vulnerable to wind dislodgement. It's super quick too - 36 units in 5 mins!. Features & Benefits Stronger fit - Starter means end units held more securely Neater finish - covers open end and fixing holes Universally handed - no need for left and right units Quick fit design - 36 units in under 5 minutes Versatile - fit to any type of roof tile High compression - roof tiles held firm in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Technical Information MeasurementValue Material PVC-u Pack Quantity 2 x Starters2 x Blanking Plates EasyVerge U system fits quickly and easily The unique design of Easy Verge U means that it can be fitted extremely quickly. In fact, this video demo shows that it's possible to fit a whole gable end of 36 units in under 5 minutes! Basic Procedure Fit optional Starter to low end of verge Position Unit over Starter with top flap over first tile Push upwards to engage with Starter and trap flap under overlapping tile Fix in place through a pre-drilled fixing hole with ring shank nails Hook next Unit under previous and pull top flap up and over Push Unit upwards engaging with previous and align with tile Nail the Unit in place and repeat for remaining units * The above fitting notes are intended as a guide, not comprehensive instructions.

Klober now even easier to fit with new Uni-Click system! Plan to use with existing dry verge? If so, you may want the older Uni-Dry system. See the difference... Also, Uni-Click units are 57mm deep, while Uni-Dry are 70mm. NEW Uni-Click Dry Verge Roof Kit from Klober (Choice of colour, end cap style and pack size) Ultimate, easy-fit gable-end roof kit! Everything needed to secure and weatherseal your roof verges. This kit includes tough and UV-stable dry verge units that fit quickly and neatly to provide attractive, mortar-free securing of most makes and profiles of concrete tile. Manufactured by Klober, a leader in roof products, versatile Uni-Click can be used with 260-350mm batten gauge on new build or existing roofs between 12.5° to 90° pitch. Contents of Dry Verge Kit Dry Verge Units (various pack sizes) Ridge End Cap (Half Round or Universal Angle) Ridge Closures (x2) Eaves Closures (x2) Uni-Click is the easy-fit successor to the Uni-Dry system from Klober. Uses the same Eaves Ridge Pack and Ridge End Caps but units are not compatible with older Uni-Dry system and can't be used together. Why Choose Uni-Click Dry Verge Uni-Click fully complies with all relevant British Standards and dry verge systems are now recognised as the best method of securing eaves roof tiles and is recommended by NHBC, the UK's largest provider of new home warranties. Quick fit system - no special tools, just click in to place and nail Resistance to Tile Uplift - roof tiles held firm, even in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Mortar-Free - not affected by expansion/contraction and sever weather Mechanical Fixings - fit with reliable fixings in any conditions What's in the Klober Uni-Click Dry Verge Roof Kit Uni-Click Dry Verge Units (Left-hand and right-hand. Choice of quantities.) Molded from durable PVC-u. Interlock neatly and fit securely, to offer a consistent appearance. Attractive and hardwearing they are also versatile, with an interlock range of 65mm that allow evenly spaced units. Find out more... Dry Verge Ridge End Cap(Half Round or Universal Angle) Klober produce two styles of hardwearing and UV safe polypropylene dry verge ridge end caps, these are the Half Round and the Universal Angle. So you can be certain that there is a style to suit your property. Find out more... Dry Verge Eaves Ridge Pack (2x eaves and 2x ridge closures) Everything needed to finsh off verges of one complete gable end. It includes two Eaves Closures, also known as Starter Blocks, two Ridge Closures and four Spiral Nails. The closures are made from hardwearing PVC-u and provide a secure mechanical fixing of Uni-Click Verge Units. Find out more... Quick and Easy Fitting The following provides a summary of the recommended steps for typical fitting of the Klober Uni-Click dry verge system. Basic Procedure Prepare verge by removing any old mortar between the tiles and undercloak. Fit Batten End Clip to end of every batten (extend tile battens 20mm beyond gable wall or bargeboard if required).* Fit Eaves Closure to end of fascia board or brickwork. Fit first Uni-Click Dry Verge unit by sliding over Eaves Closure and bottom tile, then nail to batten through Batten End Clip. Fit subsequent units (one per roof tile) until reach ridge Hooking under to engage with previous. Click it over top of previous. Slide up into position - inline with roof tile. Nail to batten through batten end clip. Insert Ridge Closure into last unit. The combs of the left and right Ridge Closure should interlock at the apex. Screw the Ridge End Cap to the ridge batten. Please note: Dry verge units can be fitted to a timber batten running from eaves to ridge rather than individual roof battens.