Maxi 132 Breather Membrane Roofing Felt from Easy-Trim (132gsm, 1m x 50m) Excellent tensile strength and nail tear resistance! Heavier and more durable 132gsm roof underlay with excellent tensile strength and nail tear resistance. Easy-Trim’s professional Maxi Breather Membrane is suitable for both fully supported and unsupported installations in tiled or slate pitch roofs. The Maxi 132 is a 3-layer micro porous breather membrane, which features a microporous film that is thermally bonded between two spun-bonded polypropylene layers. Allows the roof to breathe, so eliminates condensation, whilst providing secondary protection against rainwater ingress. Easy-Trim breather membranes improve energy efficiency and minimise the wind uplift that can loosen slates and tiles. Features & Benefits Protects roof slate and tile - reduces wind uplift Reduces condensation in roof - highly vapour permeable Driven rain and snow protection - second line of defence Highly versatile - use on warm, cold and hybrid roofs Super strong - excellent strength and nail tear resistance UV stable for 3 months - protection during construction Quality you can trust - independently tested Superior water resistance - protective polypropylene top layer Printed with brand and cutting grid - easier to identify and fit National Wind Zone Suitability New builds must comply with British Standard for Tiling and Roofing (BS5534) Annex A, with breather membranes tested against wind uplift, and their suitability for use across the 5 national wind zones. Batten GaugeWind Zone Suitability GaugeLap12345 <=345mm Batten Y Y Y     <=250mm Batten Y Y T Y Y <=345mm Taped Y Y Y Y Y Technical Information MeasurementPerformance Material 3-Layer Polypropylene Sheet (Spun Bonded Polypropylene Layer, Microporous Polypropylene Film, Spun Bonded Polypropylene Layer) Mass 132gsm Size 1m (3ft 3in) x 50m (164ft 1in) Maximum tensile force MD / CMD (N/50mm) 285 / 200 Elongation MD / CMD (%) 55 / 80 Resistance to Tearing MD / CMD (N) 145 / 175 Resistance to penetration of air (m3/m2.h.100Pa) < 0,02 Fire Class E Water Resistance Class W1 Compatibility Suitable for both fully supported and unsupported warm, cold and hybrid, tiled or slate pitch roofs. Can be used with sarking boards. Certification BS5534.2014 Annex A, Type LR Underlay to BS5250, BBA 10/4753, NSAI, CE Fitting and Usage Fitting of Easy-Trim breather membrane should begin at the lowest level of the roof, at the eaves, with the printed side facing out. Starting from the left, roll the membrane horizontally across the rafters to the right, and be sure to allow 100mm lap over the felt-support trays. The use of double-sided overlap tape to secure the lower edge to the felt-support tray is highly recommended. Roof PitchHorizontal LapsVertical Laps Not Fully SupportedFully Supported 12.5 to 14° 225 150 100 15 to 34° 150 100 100 35 to 75° 100 75 100 Horizontal laps in breather membrane should be taped with the double-sided overlap tape, or battened over. Whenever possible, horizontal laps should coincide with the closest tiling or slating batten. Vertical laps should be positioned over a rafter and have a minimum of 100mm lap. Easy-Trim breather membranes are suitable for installations on all major pitch roofing and timber frame applications, and must be installed in accordance with our fixing instructions, complying with the recommendations of BS5534: 2014 + A1: 2015; BS5250: 2011 and BS8000-0: 2014 and any other applicable standard. The products are designed to be installed by competent and experienced installers of slates and tiles.

Domed Ridge End Cap Rounded Ridge End Cap for Gable Roof Available in Grey, Brown or Terracotta. Part of the no nonsense EasyVerge U system! High quality, UV stable Domed (Half Round) plastic end cap for dry fix roof verge. For use with concrete and clay half-round segmental ridge tiles. Easy Verge U, mortar-free dry verge system is a fitters favourite. Universal units means thare is no need for seperate lefthand and righthand units and they installs quickly and easy with almost any tile type. The system also combines exceptional holding qualities, which ensures a secure fit that protects against wind dislodgement. Unique design combines ease of installation with exceptional holding, so tiles are held firmly in place and not vulnerable to wind dislodgement. It's super quick too - 36 units in 5 mins!. Features & Benefits Compatible end cap - use with Eternit, Forticrete and many more Universally handed - no need for left and right units Quick fit design - 36 units in under 5 minutes Versatile - fit to any type of roof tile High compression - roof tiles held firm in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Technical Information MeasurementValue Material PVC-u Size (length x height) Ridge End Cap - 265mm x 240mm Compatibility Ridge - Can be used with many half-round segmental ridge caps, including Marley, Forticrete and more.Verge - Use with EasyVerge U dry verge units.* * EasyVerge U Dry Verge Units and Starter Packs are available, as are Dry Verge Kits for complete gable ends. EasyVerge U system fits quickly and easily The unique design of Easy Verge U means that it can be fitted extremely quickly. In fact, this video demo shows that it's possible to fit a whole gable end of 36 units in under 5 minutes! Basic Procedure Fit optional Starter to low end of verge Position Unit over Starter with top flap over first tile Push upwards to engage with Starter and trap flap under overlapping tile Fix in place through a pre-drilled fixing hole with ring shank nails Hook next Unit under previous and pull top flap up and over Push Unit upwards engaging with previous and align with tile Nail the Unit in place and repeat for remaining units * The above fitting notes are intended as a guide, not comprehensive instructions.

EasyVerge Universal Angle Universal Angle Ridge End Cap for Gable Roof Available in Grey, Brown or Terracotta. Part of the no nonsense EasyVerge U system! High quality, UV stable Universal Angle plastic end cap for dry fix roof verge. For use with concrete and clay Angle ridge tiles. Easy Verge U, mortar-free dry verge system is a fitters favourite. Universal units means thare is no need for seperate lefthand and righthand units and they installs quickly and easy with almost any tile type. The system also combines exceptional holding qualities, which ensures a secure fit that protects against wind dislodgement. Unique design combines ease of installation with exceptional holding, so tiles are held firmly in place and not vulnerable to wind dislodgement. It's super quick too - 36 units in 5 mins!. Features & Benefits Compatible end cap - use with Eternit, Forticrete, Russell, Monier and more Universally handed - no need for left and right units Quick fit design - 36 units in under 5 minutes Versatile - fit to any type of roof tile High compression - roof tiles held firm in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Technical Information MeasurementValue Material PVC-u Size (length x height) Ridge End Cap - 265mm x 240mm System Batten Gauge 290mm – 345mm System Roof Pitch 15° to 45° Compatibility Ridge - Can be used with many Universal Angle ridge tile, including Marley, Forticrete Russell, Monier and more.Verge - Use with EasyVerge U dry verge units.* * EasyVerge U Dry Verge Units and Starter Packs are available, as are Dry Verge Kits for complete gable ends. EasyVerge U system fits quickly and easily The unique design of Easy Verge U means that it can be fitted extremely quickly. In fact, this video demo shows that it's possible to fit a whole gable end of 36 units in under 5 minutes! Basic Procedure Fit optional Starter to low end of verge Position Unit over Starter with top flap over first tile Push upwards to engage with Starter and trap flap under overlapping tile Fix in place through a pre-drilled fixing hole with ring shank nails Hook next Unit under previous and pull top flap up and over Push Unit upwards engaging with previous and align with tile Nail the Unit in place and repeat for remaining units * The above fitting notes are intended as a guide, not comprehensive instructions.

EasyVerge U Eaves Starter Park Eaves Closure fitted Close up of Eaves Closure Starter Pack for EasyVerge U Available in Grey, Brown, Terracotta or Black Part of the no nonsense, easy-fit system! Ensures secure fit of EasyVerge U units to roof verge. Includes Starters for improved fixing of eaves-end units and Blanking Plates for covering fixing holes of ridge-end units. In addition to providing a better fix, Starters also act as end caps to provide an attractive finish and prevent infestation. Part of EasyVerge U, the mortar-free system for securing almost any tile type along roof verge. EasyVerge U's unique design combines ease of installation with exceptional holding, so tiles are held firmly in place and not vulnerable to wind dislodgement. It's super quick too - 36 units in 5 mins!. Features & Benefits Stronger fit - Starter means end units held more securely Neater finish - covers open end and fixing holes Universally handed - no need for left and right units Quick fit design - 36 units in under 5 minutes Versatile - fit to any type of roof tile High compression - roof tiles held firm in strong winds Zero maintenance - years of mortar free protection High quality - tough and UV stable plastic Technical Information MeasurementValue Material PVC-u Pack Quantity 2 x Starters2 x Blanking Plates EasyVerge U system fits quickly and easily The unique design of Easy Verge U means that it can be fitted extremely quickly. In fact, this video demo shows that it's possible to fit a whole gable end of 36 units in under 5 minutes! Basic Procedure Fit optional Starter to low end of verge Position Unit over Starter with top flap over first tile Push upwards to engage with Starter and trap flap under overlapping tile Fix in place through a pre-drilled fixing hole with ring shank nails Hook next Unit under previous and pull top flap up and over Push Unit upwards engaging with previous and align with tile Nail the Unit in place and repeat for remaining units * The above fitting notes are intended as a guide, not comprehensive instructions.