60mm Main Glazing Bar from Sunwood (Choice of colour and length) Screw-Down Glazing Gasket with Aluminium Cap 60mm wide aluminium Rafter Main Glazing Bar and Cover Cap with EPDM rubber Base Gasket. Powder-coated White or Brown. Great retro-fit capping for 3 inch wooden spars. Part of the respected Sunwood Timber Glazing System. Retro-fitted to 3" rafters on existing 5-40° pitched timber roofs, the 60mm Rafter Main Bar and other Sunwood components can encase and seal problem leak areas while also breathing a new lease of life into the roof. Sunwood is equally effective on new installations too, offering an attractive, low-maintenance, long-life capping solution. This Screw-Down rafter bar includes powder-coated aluminium 60mm Rafter Main Bar Top Cap with detachable Cover Cap to conceal and protect fixings. Rafter Main Bar incorporates an integrated High Side EPDM Rubber Gasket for water-tight seal against top side of glazing and a separate EPDM Base Gasket (with removable central pip) that is fixed to timber rafter to act as a seat and seal on underside of glazing. Features & Benefits Any Glazing - use with glass or polycarbonate of any thickness High Side EPDM Gaskets - compresses onto glazing for weather-proof seal EPDM Base Gasket - acts as a seat and seal for glazing Removable Central Pip - use with grooved or non-grooved rafters Strong and lightweight - quality aluminium extrusion Quality Powder-Coating - durable, consistent finish Flexible System - fits many roof designs and sizes Fully-Serviceable - Sunwood components can be easily removed if required Maintenance-Free - no annual painting required Designed to Integrate - neatly fits other Sunwood products Easy-Fit System - designed to ease installation 5 Year Guarantee - long product guarantee Technical Information . Finishes Powder-coated White or Brown Material Aluminium extrusion (Main Bar Top Cap and Cover Cap) EPDM rubber (High Side Gaskets and Base Gasket) Top Cap Width 50mm Top Cap Height 12.73mm (excl. High Side Gasket) Base Gasket Width 50mm Base Gasket Height 8mm (uncompressed and including pip) Available Lengths 3m, 4m, 5m and 6m Fitting the Sunwood Screw-Down 60mm Rafter Main Bar Base Gaskets should be fitted to timber rafter. If timbers do not have a 3mm groove, then the central Pip that runs down the underside of the Base Gasket can be removed. Base Gasket should be cut to a length that allows it to over hand the gutter and fixed to the rafter with staples or similar. End Caps should be fitted and Main Bars cut to length. Main Bars can then be screwed down at 300mm intervals onto the timber rafters to form a nice tight seal of High Side EPDM Gasket onto the roof material. It is vital that the Main Bar Top Cap sits on the Sunwood Ridge's Flipper Seal and that the Main Bar Cover Cap is fitted and is covered by the Ridge. The Cover Cap is easy to fit using the two cover cap locators that run parallel down the length of the Main Bar - just hook the Cover Cap over one cover cap locators and pivot down onto other for a tight snap fit. The above is a summary only and not intended as comprehensive fitting instructions.

25GB Snap-Tight Glazing Bar End Cap from Sunwood Available in White and Brown Decorative and protective closure! Stylish and tough plastic End Cap form part of the Snap-Tight range of high quality, maintenance-free, Sunwood Timber Glazing System products. Protection and decorative finish to the ends of Snap-Tight 25GB Rafter Bars. Features & Benefits Use with 25GB Main and 25GB Hip bars Works with 10, 16 and 25mm glazing Easy-Fit System - simple to install Maintenance-Free - no annual painting required Technical Information MeasurementValue Finishes White or Brown Material Plastic Width 52mm Height 45mm Thickness 20mm  

End Closure for 10mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provide decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet Protects vented anti-dust breather tape Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture IMPORTANT SIZE INFORMATION These end closures are designed to fit 10mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey. Extend the life of your roof With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material. Technical Information Colours White, Chocolate Brown and Anthracite Grey Material PVC-u Glazing Thickness 10mm Length 2.1m (White and Brown), 2.5m (Anthracite Grey)

End Closure for 25mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets and glass units Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet No need to use silicone to seal the end closure Co-extruded gasket stops water penetration from above Protects vented anti-dust breather tape Prevents UV light breaking down the glass units seal Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture Extend the life of your roof With three sides protected by glazing bars and ridge capings, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure. Glass units are also protected by end closures. Even though the glass roof units are sealed they can still be damaged by the elements - UV light can break down the seal and cause the unit to fail. Technical Information Finishes White, Chocolate Brown or Anthracite Grey Material PVC-u Glazing Thickness 25mm Length 2.1m (White and Brown), 2.5m (Anthracite Grey)

Glazing Hip Bar from Sunwood Various lengths in Brown or White finish Screw-Down Hip Bar Gasket with Aluminium Cap Attractive and strong aluminium extrusion with tough powder-coated finish and long-lasting EPDM rubber gaskets. Part of the high quality, maintenance-free, Sunwood Timber Glazing System. This Screw-Down rafter hip bar includes powder-coated aluminium Rafter Hip Bar Top Cap with detachable Cover Cap to conseal and protect fixings. Rafter Hip Bar incorporates integrated High Side EPDM Rubber Gasket for water-tight seal against top side of glazing and a separate EPDM Base Gasket (with removable central pip) that is fixed to timber hip rafters to act as a seat and seal on the underside of glazing. Features & Benefits Broad Angled Profile - accomodates change in pitch Use with Jack Spars - includes ledge to cover adjoining Jack Spars Any Glazing - use with glass or polycarbonate of any thickness High Side EPDM Gaskets - compreses onto glazing for weather-proof seal EPDM Base Gasket - acts as a seat and seal for glazing Removable Central Pip - use with grooved or non-grooved rafters Strong and lightweight - quality aluminium extrusion Quality Powder-Coating - durable, consistent finish Flexible System - fits many roof designs and sizes Fully-Serviceable - Sunwood components can be easily removed if required Maintenance-Free - no annual painting required Designed to Integrate - neatly fits other Sunwood products Easy-Fit System - designed to ease installation 5 Year Guarantee - long product guarantee These Screw-Down Rafter Hip Bars should be used when fitting to hip spars of Edwardian (4-sided) and Victorian (5-sided) conservatories. The exception to this is Victorian conservatories that have a front roof pitch equal to the side pitch, which can use the standard Screw-Down Rafter Main Bars. Note that on a roof using the Sunwood Rafter Hip Bars, the Plastic Spider Top Cap should be used in favour of the aluminium cast Sunwood Spider. This allows the profile of any hip and main bars to be cut from the Spider and the Spider sit properly on the ridge. Retro-fitted to hip rafters of existing 5-40° pitched timber roofs, these Rafter Hip Bar and other Sunwood components can encase and seal problem leak areas while also breathing a new lease of life into the roof. Sunwood is equally effective on new instalations too, offering an attractive, low-maintenance, long-life capping solution. Technical Information Finishes Powder-coated White or Brown Material Aluminium extrusion (Main Bar Top Cap and Cover Cap) EPDM rubber (High Side Gaskets and Base Gasket) Top Cap Width 85.3mm Top Cap Height 23.98mm (excl. High Side Gasket) Base Gasket Width 57mm Base Gasket Height 8mm (uncompressed and including pip) Available Lengths 4m, 5m and 6m Pitch 5-40° (deviance approx 10°) Fitting the Sunwood Screw-Down Rafter Hip Bar Base Gaskets should be fitted to timber rafter. If timbers do not have a 3mm groove, then the central Pip that runs down the underside of the Base Gasket can be removed. Base Gasket should be cut to a length that allows it to over hand the gutter and fixed to the rafter with staples or similar. End Caps should be fitted and the Hip Bars cut to length before being screwed down onto the timber rafters at 300mm intervals. This will form a nice tight seal of the High Side EPDM Gasket onto the roof material. The Cover Cap is easy to fit using the two cover cap locators that run parallel down the length of the Hip Bar - just hook the Cover Cap over one cover cap locators and pivot down onto other for a tight snap fit. The above is a summary only and not intended as comprehensive fitting instructions.

25GB Snap-Tight Main Glazing Bar 10/16/25mm Panels Various lengths in Brown or White Aluminium Base Bar with PVC-u Cap and End Cap Strong, extruded aluminium Base Bar with durable PVC-u Cap and decorative End Cap - complete timber rafter main bar for 10, 16 and 25mm polycarbonate. Part of Sunwood's high quality, maintenance-free Snap-Tight range of rafter bars. The extruded aluminium Base Bars feature a central recess with locking points into which the toothed legs of the PVC-u Cap are located and long-lasting EPDM rubber gaskets to cushion and form a weather-tight seal on the underside of the polycarbonate. The PVC-u Cap has coextruded seals that forms a sound, pressure seal on the top of the polycarbonate once the PVC-u Cap has been pressed firmly into position. Retro-fitted to existing timber roofs with 10, 16 or 25mm polycarbonate, the 25GB Rafter Main Bar and other Sunwood components can encase and seal problem leak areas while also breathing a new lease of life into the roof. Sunwood is equally effective on new installations too, offering an attractive, low-maintenance, long-life capping solution. Features & Benefits Coextruded Flapper Seal - compress onto glazing for weather-proof seal EPDM Gaskets in Base - acts as a seat and seal for glazing Aluminium Base Bar - strong and lightweight extrusion Flexible System - fits many roof designs and sizes Fully-Serviceable - Sunwood components can be easily removed if required Maintenance-Free - no annual painting required Designed to Integrate - neatly fits other Sunwood products Easy-Fit System - designed to ease installation 5 Year Guarantee - long product guarantee Technical Information Materials Base Bar (Aluminium extrusion. EPDB Rubber Gaskets.) Top Cap (PVC-u) End Cap (Plastic with Metal Fixing Bracket) Top Cap Size (w x h x l) 50mm x 23mm x Various (2.5m/3m/4m/6m) Base Bar Size (w x h x l) 44mm x 21mm x Various (2.5m/3m/4m/6m) Top Cap Colour White or Brown Available Lengths 3m, 4m, 5m and 6m Fitting the Sunwood Snap-Tight 25GB Rafter Main Bar Cut Base Bars to length. Drill fixing holes in the centre of each glazing bar between the upright toothed legs. Fixings should be made at no more than 450mm intervals and around 75mm in from each end. Then ensure Base Gaskets are fitted to either side of Base Bar and screw to the rafter. You can then position the pre-cut and taped polycarbonate and fit Eaves Seal Foam as a draft excluder if desired. All that is then required is to locate the PVC-u Cap over the Base Bar and press/tap firmly into position. The above is a summary only and not intended as comprehensive fitting instructions.

End Closure for 16mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet No need to use silicone to seal the end closure Co-extruded gasket stops water penetration from above Protects vented anti-dust breather tape Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture IMPORTANT SIZE INFORMATION These end closures are designed to fit 16mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey. Extend the life of your roof With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure. Technical Information Colour White, Chocolate Brown, and Anthracite Grey Material PVC-u Glazing Thickness 16mm Length 2.1m (White and Chocolate Brown), 2.5m (Anthracite Grey)