Sunwood Screw-Down 60mm Main Glazing Bar

£50.15*

Prices incl. VAT plus shipping costs

Available, delivery time: 5 days

Colour

Anthracite Grey

Brown

White

Length

Product number: LIV-1168-1009

Product information "Sunwood Screw-Down 60mm Main Glazing Bar"

60mm Main Glazing Bar from Sunwood

(Choice of colour and length)

Screw-Down Glazing Gasket with Aluminium Cap

60mm wide aluminium Rafter Main Glazing Bar and Cover Cap with EPDM rubber Base Gasket. Powder-coated White or Brown. Great retro-fit capping for 3 inch wooden spars. Part of the respected Sunwood Timber Glazing System.

Retro-fitted to 3" rafters on existing 5-40° pitched timber roofs, the 60mm Rafter Main Bar and other Sunwood components can encase and seal problem leak areas while also breathing a new lease of life into the roof. Sunwood is equally effective on new installations too, offering an attractive, low-maintenance, long-life capping solution.

Sunwood Screw-Down 50mm Rafter Main Bar Dimensions

This Screw-Down rafter bar includes powder-coated aluminium 60mm Rafter Main Bar Top Cap with detachable Cover Cap to conceal and protect fixings. Rafter Main Bar incorporates an integrated High Side EPDM Rubber Gasket for water-tight seal against top side of glazing and a separate EPDM Base Gasket (with removable central pip) that is fixed to timber rafter to act as a seat and seal on underside of glazing.

Features & Benefits

Any Glazing - use with glass or polycarbonate of any thickness
High Side EPDM Gaskets - compresses onto glazing for weather-proof seal
EPDM Base Gasket - acts as a seat and seal for glazing
Removable Central Pip - use with grooved or non-grooved rafters
Strong and lightweight - quality aluminium extrusion
Quality Powder-Coating - durable, consistent finish
Flexible System - fits many roof designs and sizes
Fully-Serviceable - Sunwood components can be easily removed if required
Maintenance-Free - no annual painting required
Designed to Integrate - neatly fits other Sunwood products
Easy-Fit System - designed to ease installation
5 Year Guarantee - long product guarantee

Technical Information

Finishes	Powder-coated White or Brown
Material	Aluminium extrusion (Main Bar Top Cap and Cover Cap) EPDM rubber (High Side Gaskets and Base Gasket)
Top Cap Width	50mm
Top Cap Height	12.73mm (excl. High Side Gasket)
Base Gasket Width	50mm
Base Gasket Height	8mm (uncompressed and including pip)
Available Lengths	3m, 4m, 5m and 6m

Fitting the Sunwood Screw-Down 60mm Rafter Main Bar

Base Gaskets should be fitted to timber rafter. If timbers do not have a 3mm groove, then the central Pip that runs down the underside of the Base Gasket can be removed. Base Gasket should be cut to a length that allows it to over hand the gutter and fixed to the rafter with staples or similar. End Caps should be fitted and Main Bars cut to length. Main Bars can then be screwed down at 300mm intervals onto the timber rafters to form a nice tight seal of High Side EPDM Gasket onto the roof material. It is vital that the Main Bar Top Cap sits on the Sunwood Ridge's Flipper Seal and that the Main Bar Cover Cap is fitted and is covered by the Ridge. The Cover Cap is easy to fit using the two cover cap locators that run parallel down the length of the Main Bar - just hook the Cover Cap over one cover cap locators and pivot down onto other for a tight snap fit.

The above is a summary only and not intended as comprehensive fitting instructions.

Base Material:	Rubber
Capping Material:	Aluminium
Glazing Compatibility:	Glass (Double-Glazed), Glass (Single Pane), Polycarbonate (Multiwall), Polycarbonate/Acrylic (Solid)
Glazing Thickness:	10mm, 16mm, 24/25mm, 32mm, 35mm, Any
Roof Structure:	Timber Supported
Style:	Sunwood Screw-Down

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Be the first to share your insights.

Accessory Items

End Cap for Sunwood Screw-Down Glazing Main Bar for Conservatory Lean-to Roof

Sunwood Screw-Down Glazing Main Bar End Cap

Glazing Bar End Cap from Sunwood Available in White, Brown or uncoated Mill finish Powder-coated Aluminium End Cap for 50mm/60mm Main Glazing Bars Stylish and tough cast aluminium End Cap with Sunwood's recognisable Sun symbol and durable powder-coated finish. Part of the high quality, maintenance-free, Sunwood Timber Glazing System. Why buy Sunwood Screw-Down Rafter Main Bar End Caps from Truly? Features & Benefits Use with Any Screw-Down Rafter Main Bars - use with 50mm or 60mm bars Solid construction - aluminium cast Decorative - features recognisable Sun symbol Quality Powder-Coating - durable, consistent finish Fully-Serviceable - Sunwood components can be easily removed if required Maintenance-Free - no annual painting required Easy-Fit System - designed to ease installation 5 Year Guarantee - long product guarantee Technical Information Finishes Powder-coated White or Brown Material Aluminium cast Width 60mm Height 70mm Thickness 4mm Fitting the Sunwood Rafter Main Bar End Caps Fitting these End Caps is really straight forward. The End Cap is cast with a ledge on the rear that slides into the fixing channel on the Rafter Main Bar. The ledge has a pre-drilled hole that allows the supplied countersunk screw to be used to screw through and secure the End Cap to the Rafter Main Bar.

Variants from £4.23*

£6.55*

Details

16mm Polycarbonate End Closure

End Closure for 16mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet No need to use silicone to seal the end closure Co-extruded gasket stops water penetration from above Protects vented anti-dust breather tape Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture IMPORTANT SIZE INFORMATION These end closures are designed to fit 16mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey. Extend the life of your roof With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure. Technical Information Colour White, Chocolate Brown, and Anthracite Grey Material PVC-u Glazing Thickness 16mm Length 2.1m (White and Chocolate Brown), 2.5m (Anthracite Grey)

£4.44*

Details

Lean-to Roof Aluminium Wall Flashing Trim

Lean-to Roof Wall Flashing Trim

Wall Flashing Trim for Lean-to Roofs (Choice of colour and length) Protection where glazing bars meet wall! Wall flashing trim for weather-proofing lean-to roof at host wall. Made from durable powder-coated aluminium extrusion with integrated foam gasket, and suitable for most glazing bar systems, including ALUKAP-XR and SNAPA. Sealing over the wall plate, where glazing bars meet the host wall, can be troublesome, and this area is vulnerable to water ingress, so needs care and attention. This aluminium Wall Flashing is designed to help with that challenge, and can be used with the SNAPA snap-fix, and ALUKAP-XR screw-down, along with most other such glazing bar systems. Features & Benefits Protects and seals - integrated foam gasket seal Flexible application - suitable for 3-20° pitch Strong and durable - powder-coated aluminium Simple fitting - cut, silicone, screw fix, and flash Low-maintenance - no annual painting required Highly versatile - use SNAPA, ALUKAP-XR and more Did you know? This wall flashing has an expected life expectancy of over 20years! What you get with each Wall Flashing Each wall flashing is supplied as an aluminium extrusion, with closed-cell foam gasket for sealing against roof sheeting and over the top cappings. Technical Information Materials Wall Flashing Trim - Powder-coated aluminium extrusionGasket - closed-cell foam Flashing Up-stand Height 78mm Flashing Projection 104.5mm Length 2m, 3m or 6m Colour White, or Dark Brown Weight (per m) 540g Fitting the Wall Flashing Trim The following provides a brief summary of typical installation. We recommend that customers who are new to this product, refer to the manufacturers technical brochure, for further fitting advice. With bars and roof sheets in position, determine the required length of Wall Flashing and cut to size. Sit the Wall Flashing in position, and mark top capping locations on the foam gasket. At the marks, cut out gasket, to provide an even compression seal over cappings and roof sheets. Apply silicone sealant along the rear of the up-stand, which will push flush against the wall. Position Wall Flashing against wall, and push down onto bars and roof sheets. Fix to wall using suitable stainless steel screws.

Variants from £40.30*

£46.12*

Details

10mm Polycarbonate End Closure

End Closure for 10mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provide decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet Protects vented anti-dust breather tape Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture IMPORTANT SIZE INFORMATION These end closures are designed to fit 10mm thick sheets, and are supplied in 2.1m lengths for white and brown, and 2.5m length for anthracite grey. Extend the life of your roof With three sides protected by glazing bars and ridge capping, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriorate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material. Technical Information Colours White, Chocolate Brown and Anthracite Grey Material PVC-u Glazing Thickness 10mm Length 2.1m (White and Brown), 2.5m (Anthracite Grey)

Variants from £3.97*

£8.20*

Details

25mm Polycarbonate End Closure

End Closure for 25mm Polycarbonate Sheets (White, Brown or Anthracite Grey) Seal and protect the ends of your polycarbonate sheets and glass units Also known as "U" Drips, Poly End Covers and End Profile Trims, these End Closures are designed to protect ends and form a tight seal to the top of polycarbonate sheeting using it's flexible, co-extruded gasket. End closures are typically fitted to the gutter-end of pitched roofs, such as those of a conservatory, or to both ends of a free-standing roof. Provides decorative protection to the vulnerable ends of polycarbonate sheeting. Features & Benefits Seals open end of polycarbonate sheet Helps prevent dust and insects entering the sheet No need to use silicone to seal the end closure Co-extruded gasket stops water penetration from above Protects vented anti-dust breather tape Prevents UV light breaking down the glass units seal Drip design prevents water from being blown back towards the roof Drainage holes reduce condensation and moisture Extend the life of your roof With three sides protected by glazing bars and ridge capings, the gutter end is often the only edge of polycarbonate sheets that are exposed. When left exposed, the breather tape that is applied to the open fluted ends of the sheets become wet and deteriate. This leads to failure of the tape and the sheets flutes suffering condensation, algae build-up and insect penetration. Fitting End Closures helps stop this from happening. These End Closures are designed with a 3mm 'drip' on the front edge, to stop water running back towards the roofing material and drainage holes to ventilate and release any water that gets into the end closure. Glass units are also protected by end closures. Even though the glass roof units are sealed they can still be damaged by the elements - UV light can break down the seal and cause the unit to fail. Technical Information Finishes White, Chocolate Brown or Anthracite Grey Material PVC-u Glazing Thickness 25mm Length 2.1m (White and Brown), 2.5m (Anthracite Grey)

£4.82*

Details