Tapco Slate Roof Tile (100 Pack)
Product number:
TAP-1435-1020
Product information "Tapco Slate Roof Tile (100 Pack)"
Synthetic Slate Roof Tiles from Tapco (100 Pack)
Tough and lightweight imitation roof slate!
Pack of 100, synthetic roof tiles with the authentic appearance of natural slate. Tapco Slate is a lighter, tougher, unbreakable alternative to natural slate, and is also easier to work with.
Moulded from casts of natural slate, they provide an authentic texture that looks amazing - year after year, with the advantage that they do not crack, curl or fade. Designed with a curvature, called InFlex, to provide a secure and watertight fit that resists uplift and winds up to 110mph.
Installs Quickly, Looks Great, Lasts Long
Available in a range of different colours, these faux roofing tiles give homeowners, designers and architects the freedom to express.
Blended from dolomite limestone and polypropylene, they are over 50% lighter and much less fragile than natural slate, so easier to handle too.
Being tougher, they can be walked on during installation, without risk of cracking. This fact alone can reduce wastage by 15%. They're also easy to cut and fit, so quick to install.
It's no wonder that roofing contractors love to work with them.
Features & Benefits
- Lightweight - just 12kg/m² so easy to handle and needs less support
- Authentic appearance - real slate moulds and random textures
- Uplift resistance - built-in InFlex camber for tighter fit
- Consistent size - no need to sort tiles by thickness
- Easy preparation - easy to cut and no need to drill
- Faster fitting - nail, exposure and spacing markings
- Super strong - wont crack/break if dropped or walked on
- Non-fading - protection against fading under sunlight
- Lifetime warranty - fit with confidence
- Low-Pitch use - can use on roofs as low as 14°
- Complete system - compatible ridge tiles, top caps and breathable membrane
- BBA amp; BS Certified - complies with BS476 Part 3 - an AA fire rating is achieved for insulation on boarded roofs
- 100% Recyclable - conserve natural resources and reduce landfill
Special Features of Tapco Slate
- Centre Line - quick positioning of tile
- Exposure Gauge - overlap consistently
- Horizontal Spacers - space evenly across batten
- Nail Targets - fix easily with no need to drill. Markings for Half-Slate cuts included
Technical Information
| Measurement | Value |
|---|---|
| Colour | Steel Grey (formerly Pewter Grey) |
| Size | 295mm x 445mm x 5mm (11.6" x 17.5" x 0.19") |
| Weight | Nominal 0.65 Kg |
| Material | Recyclable blend of limestone and polypropylene |
| Batten Size | 38mm x 25mm (1.5" x 1") |
| Pitch | 14° to 90° |
| Fixing | Large-headed galvanised steel nails - 30mm (1.5") by 2.5mm (0.1") using hammer or nail gun. Aluminium or Copper nails may also be used but driving them through the slate may cause bending. Longer 76mm (3") nail required for fixing ridge and hips |
| Cutting | Fine-toothed handsaw, jigsaw, circular saw, or sharp utility blade |
| Storage/Temperature | Must be conditioned at a temperature no lower than 7° for 24 hours prior to use. May be installed in temperatures as low as 0° but must be hand fastened. Tapco recommends fastening with a pneumatic gun in temperatures above 7° |
| Pack Size | 100 Slates (4 x bundles of 25) |
Fitting Information
The material and the moulded markings on each slate make fitting Tapco Synthetic Tile a dream. Comprehensive fitting instructions are available if required and the following table will help judge the quantity of tile required.
| Pitch | Gauge | Slates |
|---|---|---|
| 14 to 22.5° (fully boarded) | 6" (152mm) | 22 per m2 |
| 22.5 to 25° (fully boarded, or felt and batten) | 6" (152mm) | 22 per m2 |
| 25 to 27.5° (fully boarded, or felt and batten) | 6.5" (165mm) | 20 per m2 |
| 27.5 to 30° (fully boarded, or felt and batten) | 7" (178mm) | 19 per m2 |
| Over 30° (fully boarded, or felt and batten) | 7.5" (191mm) | 18 per m2 |
Login
Accessory Items
Tapco Slate Roof Tile (25 Pack)
£81.25*
Synthetic Slate Roof Tiles from Tapco (25 Pack)
(Choice of colour available)
Tough and lightweight imitation roof slate!
Pack of 25, synthetic roof tiles with the authentic appearance of natural slate. Tapco Slate is a lighter, tougher, unbreakable alternative to natural slate, and is also easier to work with.
Moulded from casts of natural slate, they provide an authentic texture that looks amazing - year after year, with the advantage that they do not crack, curl or fade. Designed with a curvature, called InFlex, to provide a secure and watertight fit that resists uplift and winds up to 110mph.
Installs Quickly, Looks Great, Lasts Long
Available in a range of different colours, these faux roofing tiles give homeowners, designers and architects the freedom to express.
Blended from dolomite limestone and polypropylene, they are over 50% lighter and much less fragile than natural slate, so easier to handle too.
Being tougher, they can be walked on during installation, without risk of cracking. This fact alone can reduce wastage by 15%. They're also easy to cut and fit, so quick to install.
It's no wonder that roofing contractors love to work with them.
Features & Benefits
Lightweight - just 12kg/m² so easy to handle and needs less support
Authentic appearance - real slate moulds and random textures
Uplift resistance - built-in InFlex camber for tighter fit
Consistent size - no need to sort tiles by thickness
Easy preparation - easy to cut and no need to drill
Faster fitting - nail, exposure and spacing markings
Super strong - wont crack/break if dropped or walked on
Non-fading - protection against fading under sunlight
Lifetime warranty - fit with confidence
Low-Pitch use - can use on roofs as low as 14°
Complete system - compatible ridge tiles, top caps and breathable membrane
BBA amp; BS Certified - complies with BS476 Part 3 - an AA fire rating is achieved for insulation on boarded roofs
100% Recyclable - conserve natural resources and reduce landfill
Special Features of Tapco Slate
Centre Line - quick positioning of tile
Exposure Gauge - overlap consistently
Horizontal Spacers - space evenly across batten
Nail Targets - fix easily with no need to drill. Markings for Half-Slate cuts included
Technical Information
MeasurementValue
Colour
Steel Grey (formerly Pewter Grey)
Size
295mm x 445mm x 5mm (11.6" x 17.5" x 0.19")
Weight
Nominal 0.65 Kg
Material
Recyclable blend of limestone and polypropylene
Batten Size
38mm x 25mm (1.5" x 1")
Pitch
14° to 90°
Fixing
Large-headed galvanised steel nails - 30mm (1.5") by 2.5mm (0.1") using hammer or nail gun. Aluminium or Copper nails may also be used but driving them through the slate may cause bending. Longer 76mm (3") nail required for fixing ridge and hips
Cutting
Fine-toothed handsaw, jigsaw, circular saw, or sharp utility blade
Storage/Temperature
Must be conditioned at a temperature no lower than 7° for 24 hours prior to use. May be installed in temperatures as low as 0° but must be hand fastened. Tapco recommends fastening with a pneumatic gun in temperatures above 7°
Pack Size
25 Slates
Fitting Information
The material and the moulded markings on each slate make fitting Tapco Synthetic Tile a dream. Comprehensive fitting instructions are available if required and the following table will help judge the quantity of tile required.
PitchGaugeSlates
14 to 22.5° (fully boarded)
6" (152mm)
22 per m2
22.5 to 25° (fully boarded, or felt and batten)
6" (152mm)
22 per m2
25 to 27.5° (fully boarded, or felt and batten)
6.5" (165mm)
20 per m2
27.5 to 30° (fully boarded, or felt and batten)
7" (178mm)
19 per m2
Over 30° (fully boarded, or felt and batten)
7.5" (191mm)
18 per m2
Tip
Envirotile Synthetic Slate Tile
£3.95*
Envirotile Synthetic Slate Roof Tiles Plastic Roofing
(Slate Grey, Black, Brown and Terracotta)
The only tile with 8Fix locking for quick and secure fitting!
Lightweight and virtually unbreakable recycled roof tile with natural slate finish. Features a unique watertight 8Fix system that fits quickly and securely, whilst outperforming all other synthetic tiles in severe weather conditions.
Envirotile tiles interlock with adjacent and under tiles to form a more secure integrated roof covering, and uses a reduced lap that can require just 12 tiles per square metre; so reduces weight, material cost and work. Reduced weight means cheaper transportation, reduced CO² transport emissions and less structural roof requirement. Being easy to work with and approximately 50% the weight of other synthetic tiles, makes Envirotile the perfect choice for creating an authentic looking conservatory roof conversion.
Features & Benefits
Interlocking fixing - installs quickly and stops uplift
Lightweight roofing - 80% lighter than a concrete tile
Low-pitch solution - pitched from 12.5° to vertical
Virtually unbreakable - easy to transport and fit
Smaller lap - lower cost per metre and less work
Reduces build costs - easy to handle and quick to fit
Improved surface - easy grip and anti-fungal
Fully recyclable - made from recycled plastics
25 Year guarantee - long service and peace of mind
Designed and manufactured in the UK, Envirotile synthetic slate is easier to work with than traditional slate and is a complete dry fix system that requires no cement. Part of a complete solution that includes ridge, verge and eaves products.
Did you know? The Envirotile is also available as a Half Tile and Double Tile. Half Tiles can be used to initiate a weatherproof broken bond, finishing the verge, and for detailing around abutments or flashings. Double Tile can be used as a discreet filler tile for long sections, and are recommended on the ends of each course; this is especially important on hipped faces to ensure that first and last tiles have adequate fixing points.
Envirotile is weather tested to 147mph winds and fully guaranteed to perform under severe wind load throughout the UK, and is part of a complete suite, which includes membrane and tape, ridge and hip solution, eaves and ventilation.
Technical Information
MeasurementValue
Size (l x w x t)
365mm x 325mm x 11mm (half and double tile available)
Coverage (per m2)
280mm Gauge (22.5° - 90°) = 11.9 single tiles 265mm Gauge (22.5° - 90°) = 12.6 single tiles 250mm Gauge (12.5° - 22.5°) = 13.4 single tiles
Weight
645g per tile (approx. 8Kg/m2)
Material
Recycled polymer. Injection moulded using 100% of UK reliably sourced reprocessed Polypropylene.
Batten Recommendations
Battens should be 38mm x 25mm for 450mm rafter centres, and 50mm x 25mm for 600mm rafter centres.
Bond
Requires a 5mm gap between tiles for expansion, and a single or half bond can be used without need for additional fixings.
Guarantee
25 years against material product defects or failure to perform under normal use
Credentials
EN15601 – 5 times better performance than conventional tiles/slates with standard fixingsBBA Certified – conforms to BS 5534:2014BS15087:2005BS476-3 – EXT.S.AA - External Fire Exposure Roof TestDD CEN/TS 1187 test 4 – B Roof t4 - External Fire Exposure Roof TestISO 9001 CertifiedPASS Greenspec endorsed
Fixing
30mmx 3.35mm stainless steel annular ring shank (>= 25° Pitch)30mm x 4mm countersunk stainless steel screw (< 25° Pitch)
Cutting
Cuts easily with a medium toothed hand saw or powered saw, and emits no dust pollution during cutting
Storage
Envirotile should be stored on a dry flat area. Cover with tarpaulin if subject to sub-zero temperatures, and allow 24-48 hours before roof installation.
Fitting Envirotile 8Fix Synthetic Plastic Roofing Tile
Lay using the 3-step layout procedure. Extremely simple to fix, with slide locks for quick alignment and security. Can be cut equally well with hand saw or power saw, without releasing harmful dust during cutting. Half tiles, double tiles and unique eaves bar reduces material cost and work, with no need for an eaves course. The manufacturer has produced a detailed fitting guide to cover residential and commercial property, and we will be creating a dedicated Conservatory Roof Conversion Tiling Guide to support it.
Variants from £3.75*
Tapco Slate Roof Tile
£3.75*
Steel Grey Tapco Slate Tile
Roof with Tapco Slate Tile
Tapco Slate solid roof conversion
Versatile synthetic roof tile
Complete synthetic roof system
Synthetic Slate Roof Tiles from Tapco
290mm x 445mm
Tough and lightweight imitation roof slate
Authentic natural slate colour. Modern, unbreakable alternative to natural slate tile for new build and re-roofing projects. Lighter, tougher and easier to work with than real slate.
Moulded from casts of natural slate, they provide an authentic texture that looks amazing - year after year, with the advantage that they do not crack, curl or fade. Designed with a curvature, called InFlexTM, to provide a secure and watertight fit that resists uplift and winds up to 110mph.
Installs Quickly, Looks Great, Lasts Long
Available in a range of different colours, these faux roofing tiles give homeowners, designers and architects the freedom to express.
Blended from dolomite limestone and polypropylene, they are over 50% lighter and much less fragile than natural slate, so easier to handle too.
Being tougher, they can be walked on during installation, without risk of cracking. This fact alone can reduce wastage by 15%. They're also easy to cut and fit, so quick to install.
It's no wonder that roofing contractors love to work with them.
Features & Benefits
Lightweight - just 12kg/m² so easy to handle and needs less support
Authentic appearance - real slate moulds and random textures
Uplift resistance - built-in InFlex camber for tighter fit
Consistent size - no need to sort tiles by thickness
Easy preparation - easy to cut and no need to drill
Faster fitting - nail, exposure and spacing markings
Super strong - wont crack/break if dropped or walked on
Non-fading - protection against fading under sunlight
Lifetime warranty - fit with confidence
Low-Pitch use - can use on roofs as low as 14°
Complete system - compatible ridge tiles, top caps and breathable membrane
BBA amp; BS Certified - complies with BS476 Part 3 - an AA fire rating is achieved for insulation on boarded roofs
100% Recyclable - conserve natural resources and reduce landfill
Special Features of Tapco Slate
Centre Line - quick positioning of tile
Exposure Gauge - overlap consistently
Horizontal Spacers - space evenly across batten
Nail Targets - fix easily with no need to drill. Markings for Half-Slate cuts included
Technical Information
MeasurementValue
Colour
Steel Grey (formerly Pewter Grey)
Size
295mm x 445mm x 5mm (11.6" x 17.5" x 0.19")
Weight
Nominal 0.65 Kg
Material
Recyclable blend of limestone and polypropylene
Batten Size
38mm x 25mm (1.5" x 1")
Pitch
14° to 90°
Fixing
Large-headed galvanised steel nails - 30mm (1.5") by 2.5mm (0.1") using hammer or nail gun. Aluminium or Copper nails may also be used but driving them through the slate may cause bending. Longer 76mm (3") nail required for fixing ridge and hips
Cutting
Fine-toothed handsaw, jigsaw, circular saw, or sharp utility blade
Storage/Temperature
Must be conditioned at a temperature no lower than 7° for 24 hours prior to use. May be installed in temperatures as low as 0° but must be hand fastened. Tapco recommends fastening with a pneumatic gun in temperatures above 7°
Fitting Information
The material and the moulded markings on each slate make fitting Tapco Synthetic Tile a dream. Comprehensive fitting instructions are available if required and the following table will help judge the quantity of tile required.
PitchGaugeSlates
14 to 22.5° (fully boarded)
6" (152mm)
22 per m2
22.5 to 25° (fully boarded, or felt and batten)
6" (152mm)
22 per m2
25 to 27.5° (fully boarded, or felt and batten)
6.5" (165mm)
20 per m2
27.5 to 30° (fully boarded, or felt and batten)
7" (178mm)
19 per m2
Over 30° (fully boarded, or felt and batten)
7.5" (191mm)
18 per m2
Variants from £3.00*
Accessory Items
Tapco Slate Dry Verge
From
£22.50*
Tapco Slate Dry Verge
Continuous Verge for Slate
Black, 2m long
Lightweight and tough dry verge
Lightweight, durable and extremely robust dry verges for natural and synthetic slates up to 6mm thickness.
Dry Verge protects verge tiles from wind uplift and driving rain and is not vulnerable to cracking as a result of weathering and movement. Tested to survive 110MPH winds and keep water out.
Features & Benefits
Natural or synthetic tiles - use with most natural and synthetic slates upto 6mm (19/32") thick
No weathering - does not crack due to movement or weathering like bedded mortar
Neat finish - attractive continuous edge to the roof
Windproofs - prevents wind from getting behind the tiles and lifting them off the roof
Strong and durable - under normal service conditions they will provide a durable covering with a service life of in excess of 20 years
Quick and easy fitting - loved by slaters, once they have used the product, for many of the above benefits
Kind to environment - made from recyclable plastic and dolomite limestone
Lightweight - only 12kg/sq metre
BBA & BS Certified - complies with BS476 part 3 - an AA fire rating is achieved for insulation on boarded roofs
50 year guarantee - limited lifetime 50 year warranty
Tapco Slate roofing materials are the perfect modern alternative to natural slate. Made from a recyclable blend of dolomite limestone and polypropylene, the synthetic tiles/shingles and ridge look virtually identical to their natural counterparts.
Technical Information
MeasurementValue
Length
2m
Colour
Black
Material
Recyclable plastic and dolomite limestone
Weight
2kg per m2
Standards
BS476 Part 3, BBA
Guarantee
50 Years
Tapco Slate Ridge Tile
£6.25*
Steel Grey Tapco Ridge Tile
Roof with Tapco Slate Tile
Complete synthetic roof system
Synthetic Slate Ridge Tile from Tapco
Traditional slate appearance to the ridge
Authentic synthetic slate ridge tile. Lightweight, durable and extremely robust.
Moulded from casts of natural slate, they provide an authentic texture that looks amazing - year after year, and is tested to survive 110mph winds and keep water out.
The ridge tiles are flexible with a reinforced crease, which allows them to be used on pitches from 14° to over 30°.The tiles also feature a tapered end that allows the ridge tile to sit neatly and naturally overlap the adjooining ridge tile for windtight and tidy appearance.
Did you know? Ridge tiles feature exposure markings, just like the regular tile, so they can be easily aligned with uniform spacing.
Features & Benefits
Lightweight - just 12Kg/m² so easy to handle and needs less support
Authentic appearance - real slate moulds and random textures
Uplift resistance - built-in InFlex camber for tighter fit
Consistent size - no need to sort tiles by thickness
Easy preparation - easy to cut and no need to drill
Faster fitting - nail, exposure and spacing markings
Super strong - wont crack/break if dropped or walked on
Non-fading - protection against fading under sunlight
Lifetime warranty - fit with confidence
Low-Pitch use - can use on roofs as low as 14°
Complete system - compatible ridge tiles, top caps and breathable membrane
BBA & BS Certified - complies with BS476 Part 3 - an AA fire rating is achieved for insulation on boarded roofs
100% Recyclable - conserve natural resources and reduce landfill
Blended from dolomite limestone and polypropylene, they are over 50% lighter and much less fragile than natural slate, so easier to handle too.
Being tougher, they can be walked on during installation, without risk of cracking. This fact alone can reduce wastage by 15%. They're also easy to cut and fit, so quick to install.
It's no wonder that roofing contractors love to work with them.
Technical Information
MeasurementValue
Size
152mm x 457mm (6" x 18")
Weight
Nominal 0.7 Kg
Material
Recyclable blend of limestone and polypropylene
Batten Size
38mm x 25mm (1.5" x 1")
Minimum Pitch
14° (fully boarded roof)22.5° (felt/batten roof)
Maximum Pitch
90°
Fixing
Large-headed galvanised steel nails - 30mm (1.5") by 2.5mm (0.1") using hammer or nail gun. Aluminium or Copper nails may also be used but driving them through the slate may cause bending. Longer 76mm (3") nail required for fixing ridge and hips
Cutting
Fine-toothed handsaw, jigsaw, circular saw, or sharp utility blade
Storage/Temperature
Must be conditioned at a temperature no lower than 7° for 24 hours prior to use. May be installed in temperatures as low as 0° but must be hand fastened. Tapco recommends fastening with a pneumatic gun in temperatures above 7°
Colour
Steel Grey (formerly Pewter Grey)
Ridge Coverage
5.5 per linear metre
Fitting Information
The material and the moulded markings on each slate make fitting Tapco Synthetic Ridge Tile a dream. Comprehensive fitting instructions are available if required.
Variants from £5.70*