M6 Self-Tapping Concrete Anchors (5 Pack) (Available in: M6 x 50mm, 75mm or 100mm ) Get an anchor designed for the job! High quality Self Tapping Concrete Anchors that cut a thread directly into pre-drilled pilot holes, no anchor or plug is needed. Self Tapping Anchors are an excellent way to fasten a wide range of material to masonry. Really easy to use... just drill a pilot hole (see technical information below for appropriate diameter) and use socket wrench or spanner to tighten the screw, into concrete, natural stone, solid or perforated bricks, hollow blocks etc. The anchor has a high-low (aka hi-lo) relief thread to aid the removal of dust and ease insertion. The threaded anchor and self-tapping action allows for safe anchorage, with the substrate becoming the nut to the bolt - this utilises a tried and tested method for metals and wood to a broader selection of materials. These screws can be reversed and reused in the same hole - as it has cut the thread. Suitable for fixing timber battens/counter battening, window/door frames, machinery to the floor, wall plates, signs etc. Brackets or handrails, ducting, satellite dishes & aerials, trunking etc. In fact anywhere a fixing to concrete or masonry is required. Features & Benefits No expansion force - unlike plugs or anchors - you can place nearer the edge without risk of fracturing Eliminates line up problems - drill the pilot hole direct into material and substrate Suitable for a variety of substrates - concrete, solid, perforated or hollow bricks, natural stone, marble etc New easy fix - relief thread is easier to tighten especially at a lower torque than traditional plugged fixings Cuts a thread into base material - because there is no need to insert the plug and Reversed and reused - can be unscrewed and reused or reposition the object and reuse the same hole it cut Yellow Zinc Passivated - increases the resistance to corrosion High quality carbon steel - extremely hard wearing and strong - tensile strengths of 1080N/mm2 Safer - tightened using a standard wrench or spanner which is easier to control Neat finish - provides a neat finish and if removed leaves only a neat clean hole Reduces wear to bits - because they can be inserted into a shallower hole that traditional plugged fixings Utilises standardised dimensions - M6, M8, M10 or M12 Dimensions stamped on head - easier to identify for post inspection and if loose out of box 1 Piece design - means that there are no other pieces to lose unlike sleeved anchors Technical Information Specification Summary: M Standard Diameter M6 M8 M10 M12 Lengths available (mm) 50 75 100 60 75 100 130 150 75 100 130 150 75 100 130 150 200 Pilot Hole / Bit required 6mm 8mm 10mm 12mm Shear Force 2.2kN 3.6kN 4.2kN 4.6kN Pilot Hole / Bit required 6mm 8mm 10mm 12mm Bolt Head Diameter 10mm 15mm 17mm 19mm Minimum embedment depth 30mm 40mm 50mm 60mm Head type Hex head Finish Yellow Zinc Passivated Material Extremely high quality carbon steel tensile strengths of 1080N/mm2 Thread type Self tapping with relief thread Head type Hex head How do I install the anchor? Wear appropriate safety gear - eye and ear protection Determine where the anchor is going to be placed Using an 8mm bit drill a pilot hole to the correct depth into the substrate Hoover out the hole to remove debris Manoeuvre the object being fastened into position Install the concrete anchor using a socket wrench or spanner to ensure that the anchor is not over tightened and strip the thread Quick Tip: if you do not have a depth gauge on your drill add a piece of tape onto the drill bit acting as a mark for where to stop drilling. Important Notes:- Stated length of the anchor is from the underneath of the head Clearance hole diameter in attached object to be fixed for an M12 anchor is 14mm Recommend using manual tools to drive the anchor for more control and safety - using a drill can strip the thread or damage the hole

M12 Self-Tapping Concrete Anchors (5 Pack) (Available in: M12 x 75mm, 100mm, 130mm, 150mm or 200mm ) Get an anchor designed for the job! High quality Self Tapping Concrete Anchors that cut a thread directly into pre-drilled pilot holes, no anchor or plug is needed. Self Tapping Anchors are an excellent way to fasten a wide range of material to masonry. Really easy to use... just drill a pilot hole (see technical information below for appropriate diameter) and use socket wrench or spanner to tighten the screw, into concrete, natural stone, solid or perforated bricks, hollow blocks etc. The anchor has a high-low (aka hi-lo) relief thread to aid the removal of dust and ease insertion. The threaded anchor and self-tapping action allows for safe anchorage, with the substrate becoming the nut to the bolt - this utilises a tried and tested method for metals and wood to a broader selection of materials. These screws can be reversed and reused in the same hole - as it has cut the thread. Suitable for fixing timber battens/counter battening, window/door frames, machinery to the floor, wall plates, signs etc. Brackets or handrails, ducting, satellite dishes & aerials, trunking etc. In fact anywhere a fixing to concrete or masonry is required Features & Benefits No expansion force - unlike plugs or anchors - you can place nearer the edge without risk of fracturing Eliminates line up problems - drill the pilot hole direct into material and substrate Suitable for a variety of substrates - concrete, solid, perforated or hollow bricks, natural stone, marble etc New easy fix - relief thread is easier to tighten especially at a lower torque than traditional plugged fixings Cuts a thread into base material - because there is no need to insert the plug Reversed and reused - can be unscrewed & reused or reposition the object & reuse the same hole it cut Yellow Zinc Passivated - increases the resistance to corrosion High quality carbon steel - extremely hard wearing and strong - tensile strengths of 1080N/mm2 Safer - tightened using a standard wrench or spanner which is easier to control Neat finish - provides a neat finish and if removed leaves only a neat clean hole Reduces wear to bits - because they can be inserted into a shallower hole that traditional plugged fixings Utilises standardised dimensions - M6, M8, M10 or M12 Dimensions stamped on head - easier to identify for post inspection and if loose out of box 1 Piece design - means that there are no other pieces to lose unlike sleeved anchors FAQ's Advice & Specifications Save money - what size anchor do I need? The length of the anchor needed can be worked out by adding the minimum embedment depth (50mm for a M10) to the object being fixed depth, this will give the length of the anchor required. For example if the depth of the object being fixed is 45mm and the minimum embedment depth is 50mm that is 45 + 50 = 95 rounded to the nearest size in the range that means a 100mm anchor should be used. Using this simple calculation can save you money! What depth do I drill the pilot hole? The depth you need to drill the pilot hole is worked out by subtracting the objects depth from the stated anchor length and then add 5mm. For example if the anchor is 100mm and the object being fixed is 45mm that is 100 - 45 + 5 = 60 the depth of the pilot hole needed is 60mm. Technical Information Specification Summary: Pilot Hole / Bit required 6mm 8mm 10mm 12mm M Standard Diameter M6 M8 M10 M12 Lengths available (mm) 50 75 100 60 75 100 130 150 75 100 130 150 75 100 130 150 200 Pilot Hole / Bit required 6mm 8mm 10mm 12mm Shear Force 2.2kN 3.6kN 4.2kN 4.6kN Bolt Head Diameter 10mm 15mm 17mm 19mm Minimum embedment depth 30mm 40mm 50mm 60mm Head type Hex head Finish Yellow Zinc Passivated Material Extremely high quality carbon steel tensile strengths of 1080N/mm2 Thread type Self tapping with relief thread Head type Hex head How do I install the anchor? Wear appropriate safety gear - eye and ear protection Determine where the anchor is going to be placed Using an 8mm bit drill a pilot hole to the correct depth into the substrate Hoover out the hole to remove debris Manoeuvre the object being fastened into position Install the concrete anchor using a socket wrench or spanner to ensure that the anchor is not over tightened and strip the thread Quick Tip: if you do not have a depth gauge on your drill add a piece of tape onto the drill bit acting as a mark for where to stop drilling. Important Notes:- Stated length of the anchor is from the underneath of the head Clearance hole diameter in attached object to be fixed for an M12 anchor is 14mm Recommend using manual tools to drive the anchor for more control and safety - using a drill can strip the thread or damage the hole

20 x Deltaleigh Nylon Frame Fixings - M10 M10 x 80mm, 100mm, 120mm or 160mm Get a screw designed for the job! High quality Nylon Frame Hammer Screw Fixings solves the problem of unequal masonry opening. Available in a wide range of sizes. Used to fix windows, doors and conservatory frames to masonry walls - such as brick, stone or concrete - offering a quick, efficient and cost effective way to fix into solid material giving good results. Manufactured from virgin nylon, countersunk frame fixings comes complete with a steel pozi, cross screw head being zinc and yellow passivated for corrosion resistance. The screw can be removed and reused or adjusted for re-alignment of the bracket etc with alignment adjustment slots. Suitable for fixing uPVC timber or metal window or door frames. Used on concrete, stone, brick or blockwork substrates etc. Features & Benefits Tough Nylon plug - prevents frame distortion during tightening Anti-Rotation lugs - 2 lugs on the sleeve help prevent rotation of the sleeve Suitable for a variety of substrates - concrete, solid, perforated or hollow bricks, natural stone etc Corrosion resistance - zinc and yellow passivated screws help resist corrosion Wide range of sizes - from 60mm to 140mm in M8 or M10 Corrosion resistance - zinc and yellow passivated screws help resist corrosion Technical Information Specification Summary: Length M8 60mm M8 or M10 80mm M8 or M10 100mm M8 or M10 120mm M8 140mm Head diameter 11mm Anchor fixing diameter M8 - 8mm or M10 - 10mm Head type Countersunk pozi 3 head Drill bit required (hole) M8 - 8mm bit or M10 - 10mm bit

M8 Self-Tapping Concrete Anchors (5 Pack) (Available in: M8 x 60mm, 75mm, 100mm, 130mm or 150mm) Get an anchor designed for the job! High quality Self Tapping Concrete Anchors that cut a thread directly into pre-drilled pilot holes, no anchor or plug is needed. Self Tapping Anchors are an excellent way to fasten a wide range of material to masonry. Really easy to use... just drill a pilot hole (see technical information below for appropriate diameter) and use socket wrench or spanner to tighten the screw, into concrete, natural stone, solid or perforated bricks, hollow blocks etc. The anchor has a high-low (aka hi-lo) relief thread to aid the removal of dust and ease insertion. The threaded anchor and self-tapping action allows for safe anchorage, with the substrate becoming the nut to the bolt - this utilises a tried and tested method for metals and wood to a broader selection of materials. These screws can be reversed and reused in the same hole - as it has cut the thread. Suitable for fixing timber battens/counter battening, window/door frames, machinery to the floor, wall plates, signs etc. Brackets or handrails, ducting, satellite dishes & aerials, trunking etc. In fact anywhere a fixing to concrete or masonry is required. Features & Benefits No expansion force - unlike plugs or anchors - you can place nearer the edge without risk of fracturing Eliminates line up problems - drill the pilot hole direct into material and substrate Suitable for a variety of substrates - concrete, solid, perforated or hollow bricks, natural stone, marble etc New easy fix - relief thread is easier to tighten especially at a lower torque than traditional plugged fixings Cuts a thread into base material - because there is no need to insert the plug Reversed and reused - can be unscrewed and reused or reposition the object and reuse the same hole it cut Yellow Zinc Passivated - increases the resistance to corrosion High quality carbon steel - extremely hard wearing and strong - tensile strengths of 1080N/mm2 Safer - tightened using a standard wrench or spanner which is easier to control Neat finish - provides a neat finish and if removed leaves only a neat clean hole Reduces wear to bits - because they can be inserted into a shallower hole that traditional plugged fixings Utilises standardised dimensions - M6, M8, M10 or M12 Dimensions stamped on head - easier to identify for post inspection and if loose out of box 1 Piece design - means that there are no other pieces to lose unlike sleeved anchors Technical Information Specification Summary: M Standard Diameter M6 M8 M10 M12 Lengths available (mm) 50 75 100 60 75 100 130 150 75 100 130 150 75 100 130 150 200 Pilot Hole / Bit required 6mm 8mm 10mm 12mm Shear Force 2.2kN 3.6kN 4.2kN 4.6kN Pilot Hole / Bit required 6mm 8mm 10mm 12mm Bolt Head Diameter 10mm 15mm 17mm 19mm Minimum embedment depth 30mm 40mm 50mm 60mm Head type Hex head Finish Yellow Zinc Passivated Material Extremely high quality carbon steel tensile strengths of 1080N/mm2 Thread type Self tapping with relief thread Head type Hex head How do I install the anchor? Wear appropriate safety gear - eye and ear protection Determine where the anchor is going to be placed Using an 8mm bit drill a pilot hole to the correct depth into the substrate Hoover out the hole to remove debris Manoeuvre the object being fastened into position Install the concrete anchor using a socket wrench or spanner to ensure that the anchor is not over tightened and strip the thread Quick Tip: if you do not have a depth gauge on your drill add a piece of tape onto the drill bit acting as a mark for where to stop drilling. Important Notes:- Stated length of the anchor is from the underneath of the head Clearance hole diameter in attached object to be fixed for an M12 anchor is 14mm Recommend using manual tools to drive the anchor for more control and safety - using a drill can strip the thread or damage the hole