Flat PVCu Door Panel (Choice of size and thickness) Low cost replacement uPVC panel Tough flat half panel with Polystyrene infill between UV stable PVC-u sheets. White with attractive smooth finish, these half panels are easy to cut and fit. Commonly used to replace damaged panels in PVC-u and aluminium doors or conservatory frames and to blank off unwanted glazed panels. A reinforced version of this panel, offering increased security, is also available. Features & Benefits Standard white matches most profiles Colourfast and UV stable High impact and chemical resistance Manufactured to industry standards Fire-resistant and self-extinguishing Weatherproof and rot resistant Totally recyclable and non-toxic Manufactured in accordance with BS 476 Part 7 - Spread of Flame Class 1 and BS 4735, with self-extinguishing fire retardant materials and fulfils Part L Building Regulations. Technical Information MeasurementValue Panel Sizes (w x h) 750mm x 750mm*1500mm x 750mm*2150mm x 750mm* Panel Thickness 20mm, 24mm or 28mm* Outer Skin 1.5mm PVC-u sheet Infill Material Polystyrene** Colour White 626 Standards Compliance Part L Building Regulations, BS 476 Part 7 - Spread of Flame Class 1, BS 4735. * Allow cutting and manufacturing tolerances of ±5mm (width and height), and ±2mm (thickness).** Polystyrene with MDF reinforcement is available. Fitting PVC-u Door Panels Fitting the panels is fairly straight forward, but we offer 5 useful pointers to bear in mind. Leave protective film in place to prevent scratches during handling. Be sure to peel off before fitting, or peel back from the edges, so that it does not get trapped by the beads. A decorators paint scraper or similar tool can be used to remove any beads. When removing, it is easier to start with the longer ones. When replacing beads, the longer ones should be done last. As you remove beads, mark the back of them to identify where they came from (ie. top, right, bottom, left) as they should be put back in the same position. When measuring and cutting to size, remember the phrase 'measure twice - cut once'. Be sure the measurement is correct, as a cut can't be undone. Fine toothed handsaw or jigsaw blade is most suitable for cutting the panels. Soft headed hammers can be used to encourage reluctant beads to go back in when they are fitted nice and tight. Remember that cold temperature can make PVC-u brittle.    

Reinforced Panel with Twin Moulding 20mm, 24mm or 28mm thick Classic decorative moulding inside and out Attractive reinforced half panel with twin rectangular moulding on both sides. Features a Polystyrene inner with strong MDF core between tough UV stable white PVC-u skins. These raised half panels are easy to cut and fit. Commonly used to replace damaged panels in PVC-u and aluminium doors or conservatory frames and to blank off unwanted glazed panels. Features & Benefits Stronger and more secure with MDF reinforcement Standard white matches most profiles Colourfast and UV stable High impact and chemical resistance Manufactured to industry standards Fire-resistant and self-extinguishing Weatherproof and rot resistant Totally recyclable and non-toxic Attractive twin decoration to both sides Manufactured in accordance with BS 476 Part 7 - Spread of Flame Class 1 and BS 4735, with self-extinguishing fire retardant materials and fullfils Part L Building Regulations. Technical Information MeasurementValue Panel Size (w x h) 700mm x 900mm* Panel Thickness 20mm, 24mm or 28mm* Individual Moulding Size (w x h) 200mm x 530mm Combined Moulding Area (w x h) 500mm x 530mm Outer Skin 1.5mm PVC-u sheet Infill Material Polystyrene and 4mm MDF board Colour White 626 Standards Compliance Part L Building Regulations, BS 476 Part 7 - Spread of Flame Class 1, BS 4735. Minimum Cut Size (W x H) 550mm x 580mm * Allow cutting and manufacturing tolerances of ±5mm (width and height), and ±2mm (thickness). Fitting PVC-u Door Half Panels Fitting the panels is fairly straight forward, but we offer 5 useful pointers to bear in mind. Leave protective film in place to prevent scratches during handling. Be sure to peel off before fitting, or peel back from the edges, so that it does not get trapped by the beads. A decorators paint scraper or similar tool can be used to remove any beads. When removing, it is easier to start with the longer ones. When replacing beads, the longer ones should be done last. As you remove beads, mark the back of them to identify where they came from (ie. top, right, bottom, left) as they should be put back in the same position. When measuring and cutting to size, remember the phrase 'measure twice - cut once'. Be sure the measurement is correct, as a cut can't be undone. Fine toothed handsaw or jigsaw blade is most suitable for cutting the panels. Soft headed hammers can be used to encourage reluctant beads to go back in when they are fitted nice and tight. Remember that cold temperature can make PVC-u brittle.

Golden Oak uPVC Flat Door Panel Available in multiple thicknesses and finishes! Heat-resistant and fire-retardant technology with added reinforcement. Golden Oak reinforced flat PVCu infill panel with authentic UV stable woodgrain. An easy to install MDF strengthened replacement for damaged panels, replacement of glass units or removal of cat flaps. The insulated interior of this panel, manufactured with advanced technology techniques bonds together fire-retardant type A polystyrene foam and MDF using a vacuum formed and pressure bonded process to add superior strength and security to both uPVC skins. The exterior meanwhile, available in a choice of 2 finishes is composed of 2 highly durable uPVC skins, bonded to the internal core while the heat resistant technology of the foiled woodgrain finish helps maintain the integrity and protect from blistering and cracking, thermal distortion and UV discolouration. Please note the grain runs along the 700mm length of the panel. Features & Benefits UPVC - superior scratch and abrasion resistance Options - available in multiple finishes and thicknesses Strength - pressure bonded MDF and skin for extra reinforcement Heat-Resistant Technology - looks and performs better for longer Fire-Retardant - specially formulated to restrict burning Environmentally Friendly - totally recyclable and non-toxic Guaranteed up to 5 years against cracking and UV discolouration. Manufactured in accordance with BS 476 Part 7 - Spread of Flame Class 1 and BS 4735, with self-extinguishing fire-retardant materials and fulfils Part L Building Regulations. Technical Information Technical Specification Pnael Size (w x h) 700mm x 900mm* Thickness 24mm or 28mm* Material UPVC Infill Material Foam and MDF Finish and Colour Finished on the outside in Golden Oak with a choice of internal colour of Golden Oak or White Standards Compliance Part L Building Regulations, BS 476 Part 7 - Spread of Flame Class 1, BS 4735 Guarantee 5 years against cracking and UV discolouration * Allow cutting and manufacturing tolerances of ±5mm (width and height), and ±2mm (thickness).

Flat Reinforced PVC-u Door Panel (Choice of size and thickness) Strong MDF inner for increased security Tough flat panel with MDF reinforcement inside a Polystyrene infill sandwiched between UV stable PVC-u sheets. White with attractive smooth finish, these half panels are easy to cut and fit. Commonly used to replace damaged panels in PVC-u and aluminium doors or conservatory frames and to blank off unwanted glazed panels. A non-reinforced version of this panels available if increased security is not essential. Features & Benefits Stronger and more secure with MDF reinforcement Standard white matches most profiles Colourfast and UV stable High impact and chemical resistance Manufactured to industry standards Fire-resistant and self-extinguishing Weatherproof and rot resistant Totally recyclable and non-toxic Manufactured in accordance with BS 476 Part 7 - Spread of Flame Class 1 and BS 4735, with self-extinguishing fire retardant materials and fulfils Part L Building Regulations. Technical Information MeasurementValue Panel Sizes (w x h) 750mm x 750mm*1500mm x 750mm*2150mm x 750mm* Panel Thickness 20mm, 24mm or 28mm* Outer Skin 1.5mm PVC-u sheet Infill Material Polystyrene and 4mm MDF board Colour White 626 Standards Compliance Part L Building Regulations, BS 476 Part 7 - Spread of Flame Class 1, BS 4735. * Allow cutting and manufacturing tolerances of ±5mm (width and height), and ±2mm (thickness). Fitting PVC-u Door Panels Fitting the panels is fairly straight forward but we offer 5 useful pointers to bear in mind. Leave protective film in place to prevent scratches during handling. Be sure to peal off before fitting, or peel back from the edges, so that it does not get trapped by the beads. A decorators paint scraper or similar tool can be used to remove any beads. When removing, it is easier to start with the longer ones. When replacing beads, the longer ones should be done last. As you remove beads, mark the back of them to identify where they came from (ie. top, right, bottom, left) as they should be put back in the same position. When measuring and cutting to size, remember the phrase 'measure twice - cut once'. Be sure the measurement is correct as a cut can't be undone. Fine toothed handsaw or jigsaw blade is most suitable for cutting the panels. Soft headed hammers can be used to encourage reluctant beads to go back in when they are fitted nice and tight. Remember that cold temperature can make PVC-u brittle.