Wall Flashing Trim for Lean-to Roofs (Choice of colour and length) Protection where glazing bars meet wall! Wall flashing trim for weather-proofing lean-to roof at host wall. Made from durable powder-coated aluminium extrusion with integrated foam gasket, and suitable for most glazing bar systems, including ALUKAP-XR and SNAPA. Sealing over the wall plate, where glazing bars meet the host wall, can be troublesome, and this area is vulnerable to water ingress, so needs care and attention. This aluminium Wall Flashing is designed to help with that challenge, and can be used with the SNAPA snap-fix, and ALUKAP-XR screw-down, along with most other such glazing bar systems. Features & Benefits Protects and seals - integrated foam gasket seal Flexible application - suitable for 3-20° pitch Strong and durable - powder-coated aluminium Simple fitting - cut, silicone, screw fix, and flash Low-maintenance - no annual painting required Highly versatile - use SNAPA, ALUKAP-XR and more Did you know? This wall flashing has an expected life expectancy of over 20years! What you get with each Wall Flashing Each wall flashing is supplied as an aluminium extrusion, with closed-cell foam gasket for sealing against roof sheeting and over the top cappings. Technical Information Materials Wall Flashing Trim - Powder-coated aluminium extrusionGasket - closed-cell foam Flashing Up-stand Height 78mm Flashing Projection 104.5mm Length 2m, 3m or 6m Colour White, or Dark Brown Weight (per m) 540g Fitting the Wall Flashing Trim The following provides a brief summary of typical installation. We recommend that customers who are new to this product, refer to the manufacturers technical brochure, for further fitting advice. With bars and roof sheets in position, determine the required length of Wall Flashing and cut to size. Sit the Wall Flashing in position, and mark top capping locations on the foam gasket. At the marks, cut out gasket, to provide an even compression seal over cappings and roof sheets. Apply silicone sealant along the rear of the up-stand, which will push flush against the wall. Position Wall Flashing against wall, and push down onto bars and roof sheets. Fix to wall using suitable stainless steel screws.

45mm Aluminium Capping for Timber Roofs Choice of colour, length and base gasket Discreet profile. Superior weatherproofing! Premium quality, Inner Capping for 45mm (1 3/4") timber rafters. The Main Bar comes as three parts, a mill-finished aluminium Inner Capping, an aluminium powder-coated Outer Capping and cast aluminium End Cap. The Inner Capping features rubber gaskets and creates a water-tight seal over the glazing when screwed to the rafter. All fixings are concealed and water ingress eliminated by the durable Outer Capping which snap-fixes securely over the Inner Capping. A heavy duty End Cap provides secure and decorative closure to end of bars, while helping to prevent slippage of Outer Capping and glazing material. Base Gaskets, which sit directly on timber rafters underneath the glazing material, can be supplied to provide a rubber seal under glazing material if required. Features & Benefits Extruded aluminium - strong and lightweight Maintenance-free - no annual painting required Durable powder-coating - no discolouring Long-life material - no warping or cracking Quick and simple - pre-drilled Inner Capping with snap-fix Outer Capping Custom colour option - can paint to any RAL colour Attractive profile - low contour with concealed gaskets Compatible with glass - unlick most Snap-Tight systems Shape and height of the 45mm Main Bar compliments the 60mm version, so can be used together on the same roof. The 45mm Main Bars are available in a choice of colour, length and with or without 45mm and 55mm base gaskets. Custom Colour Option - There's no problem if you want to match an existing RAL colour. Just choose 'Custom Colour' when ordering and contact us to provide the RAL code. Technical Information PropertyValue Finish Powder-coated. White, Dark Brown or Custom Colour (specify RAL code). Material Aluminium extrusion (Inner Capping and Outer Capping) EPDM rubber (Glazing Seal Gaskets and Base Gasket) Width 45mm Height 20mm Length 3m, 3.6m, 4.8m or 6m Base Gasket Option None, 45mm or 55mm Weight 720g per metre (approx) Fitting ALUKAP-XR Main Bar Cut the Inner Capping and rubber gaskets to desired length Insert gasket into Inner Capping gasket grooves If using, fix Base Gasket to timber rafter before laying glazing material Position Inner Capping on glazing, directly over rafter Drill pilot holes through pre-drilled holes in Inner Capping Screw Inner Capping down to create a uniform seal on glazing material - be careful not to over-tightening Screw the End Cap in place Use sealant to make additional seals around abutments or connections to walls, hip bars or ridge bars if required Cut Outer Capping to required length and snap-fix on to the Inner Capping The above is offered only as a guide and not as complete fitting instructions for all scenarios.

60mm Aluminium Capping for Wall Rafter Choice of colour, length and base gasket Superior sealing at wall abutment! Premium quality, Inner Capping for 60mm (2 9/25") timber rafters abutting a wall. The Wall Bar comes as three parts, a mill-finished aluminium Inner Capping, an aluminium powder-coated Wall Outer Capping and cast aluminium End Cap. The Inner Capping gets screwed to a rafter and its rubber gaskets create a water-tight seal over the glazing. The durable Wall Outer Capping snap-fixes securely over the Inner Capping to conceal fixings and prevent water ingress. Wall Outer Capping extends upwards to form a high up-stand that can be over-flashed if required. A heavy duty End Cap provides secure and decorative closure to end of bars, while helping to prevent slippage of glazing material. Base Gaskets, which sit directly on timber rafters underneath the glazing material, can be supplied to provide a rubber seal under glazing material if required. Features & Benefits Extruded aluminium - strong and lightweight Maintenance-free - no annual painting required Durable powder-coating - no discolouring Long-life material - no warping or cracking Quick and simple - pre-drilled Inner Capping with snap-fix Wall Outer Capping Custom colour option - can paint to any RAL colour Attractive profile - low contour with concealed gaskets Compatible with glass - unlick most Snap-Tight systems Shape and height of the 60mm Wall Bar compliments the 45mm and 60mm Main Bar, so can be used together on the same roof. It is available in a choice of colour, length and with or without 45mm and 55mm base gaskets. Custom Colour Option - There's no problem if you want to match an existing RAL colour. Just choose 'Custom Colour' when ordering and contact us to provide the RAL code. Technical Information PropertyValue Finish Powder-coated. White, Dark Brown or Custom Colour (specify RAL code). Material Aluminium extrusion (Inner Capping and Outer Capping) EPDM rubber (Glazing Seal Gaskets and Base Gasket) Width 60mm Height 20mm (60mm including upstand) Length 3m, 3.6m, 4.8m or 6m Base Gasket Option None, 45mm or 55mm Weight 1027g per metre (approx) Fitting ALUKAP-XR Wall Bar Cut the Inner Capping and rubber gaskets to desired length Insert gasket into Inner Capping gasket grooves If using, fix Base Gasket to timber rafter before laying glazing material Position Inner Capping on glazing, directly over rafter Drill pilot holes through pre-drilled holes in Inner Capping Screw Inner Capping down to create a uniform seal on glazing material - be careful not to over-tightening* Screw the End Cap in place Use sealant to make additional seals around abutments or connections to walls, hip bars or ridge bars if required Cut Wall Outer Capping to required length and snap-fix on to the Inner Capping** * If fitting with glass, or polycarbonate, which does not extend across rafter to wall, then a timber packer should be used to the same height as the glazing material. ** Ribbed backing of upstand is a suitable surface for sealant and the upstand can be over flashed. The above is offered only as a guide and not as complete fitting instructions for all scenarios.

Aluminium Capping for Timber Hip Rafters Choice of colour, length and base gasket Clean and simple hip protection! Premium quality, Inner Capping for clean and simple hip connections. The Hip Bar comes as three parts, a mill-finished aluminium Inner Capping, an aluminium powder-coated Hip Outer Capping and cast aluminium End Cap. The Inner Capping features rubber gaskets and creates a water-tight seal over the glazing when screwed to the rafter. The durable Hip Outer Capping snap-fixes securely over the Inner Capping and extends outwards to offer umbrella protection to jack spars joining the hip. All fixings are concealed and water ingress eliminated. A heavy duty End Cap provides secure and decorative closure to end of bars, while helping to prevent slippage of Hip Outer Capping and glazing material. Base Gaskets, which sit directly on timber rafters underneath the glazing material, can be supplied to provide a rubber seal under glazing material if required. Features & Benefits Extruded aluminium - strong and lightweight Maintenance-free - no annual painting required Durable powder-coating - no discolouring Long-life material - no warping or cracking Quick and simple - pre-drilled Inner Capping with snap-fix Outer Capping Custom colour option - can paint to any RAL colour Attractive profile - low contour with concealed gaskets Compatible with glass - unlick most Snap-Tight systems The Hip Bar can be used with both 45mm and 60mm Main Bars and are available in a choice of colour, length and with or without 45mm and 55mm base gaskets. Custom Colour Option - There's no problem if you want to match an existing RAL colour. Just choose 'Custom Colour' when ordering and contact us to provide the RAL code. Technical Information PropertyValue Finish Powder-coated. White, Dark Brown or Custom Colour (specify RAL code). Material Aluminium extrusion (Inner Capping and Outer Capping) EPDM rubber (Glazing Seal Gaskets and Base Gasket) Width 60mm (80mm including the overhang) Height 33mm Length 3m, 3.6m, 4.8m or 6m Base Gasket Option None, 45mm or 55mm Weight 1Kg per metre (approx) Fitting ALUKAP-XR Hip Bar Cut the Inner Capping and rubber gaskets to desired length Insert gasket into Inner Capping gasket grooves If using, fix Base Gasket to timber rafter before laying glazing material Position Inner Capping on glazing, directly over rafter Drill pilot holes through pre-drilled holes in Inner Capping Screw Inner Capping down to create a uniform seal on glazing material - be careful not to over-tightening Screw the End Cap in place Use sealant to make additional seals around abutments or connections to walls, hip bars or ridge bars if required Cut Outer Capping to required length and snap-fix on to the Inner Capping* * Outer Capping should be fitted once any required sealing has been made. Typical sealing includes around adjoining jackspars against the raised side. The above is offered only as a guide and not as complete fitting instructions for all scenarios.

60mm Aluminium Capping for Gable End Rafter Choice of colour, length and base gasket Attractive closure. Superior sealing! Premium quality, Inner Capping for 60mm (2 9/25") timber gable end rafters. The Gable Bar comes as three parts, a mill-finished aluminium Inner Capping, an aluminium powder-coated Gable Outer Capping and cast aluminium End Cap. The Inner Capping gets screwed to a rafter and its rubber gaskets create a water-tight seal over the glazing. The durable Gable Outer Capping snap-fixes securely over the Inner Capping to conceal fixings and prevent water ingress. The Gable Outer Capping extends down on the open side to form a deep drip that cloaks over the end rafter. A heavy duty End Cap provides secure and decorative closure to end of bars, while helping to prevent slippage of Gable Outer Capping and glazing material. Base Gaskets, which sit directly on timber rafters underneath the glazing material, can be supplied to provide a rubber seal under glazing material if required. Features & Benefits Extruded aluminium - strong and lightweight Maintenance-free - no annual painting required Durable powder-coating - no discolouring Long-life material - no warping or cracking Quick and simple - pre-drilled Inner Capping with snap-fix Gable Outer Capping Custom colour option - can paint to any RAL colour Attractive profile - low contour with concealed gaskets Compatible with glass - unlick most Snap-Tight systems Shape and height of the 45mm Gable Bar compliments the 45mm and 60mm Main Bar, so can be used together on the same roof. It is available in a choice of colour, length and with or without 45mm and 55mm base gaskets. Custom Colour Option - There's no problem if you want to match an existing RAL colour. Just choose 'Custom Colour' when ordering and contact us to provide the RAL code. Technical Information PropertyValue Finish Powder-coated. White, Dark Brown or Custom Colour (specify RAL code). Material Aluminium extrusion (Inner Capping and Outer Capping) EPDM rubber (Glazing Seal Gaskets and Base Gasket) Width 60mm Height 20mm (65mm including drip face) Length 3m, 3.6m, 4.8m or 6m Base Gasket Option None, 45mm or 55mm Weight 940g per metre (approx) Fitting ALUKAP-XR Gable Bar Cut the Inner Capping and rubber gaskets to desired length Insert gasket into Inner Capping gasket grooves If using, fix Base Gasket to timber rafter before laying glazing material Position Inner Capping on glazing, directly over rafter Drill pilot holes through pre-drilled holes in Inner Capping Screw Inner Capping down to create a uniform seal on glazing material - be careful not to over-tightening Screw the End Cap in place Use sealant to make additional seals around abutments or connections to walls, hip bars or ridge bars if required Cut Gable Outer Capping to required length and snap-fix on to the Inner Capping The above is offered only as a guide and not as complete fitting instructions for all scenarios.